Описание
Уязвимость модуля drivers/usb/chipidea/udc.c ядра операционных систем Linux связана с некорректной работой шины USB независимо от отключения контроллера USB-устройства в результате неправильной блокировки ресурсов. Эксплуатация уязвимости может позволить нарушителю вызвать отказ в обслуживании
Вендор
Наименование ПО
Версия ПО
Тип ПО
Операционные системы и аппаратные платформы
Уровень опасности уязвимости
Возможные меры по устранению уязвимости
Статус уязвимости
Наличие эксплойта
Информация об устранении
Ссылки на источники
Идентификаторы других систем описаний уязвимостей
- CVE
EPSS
5.5 Medium
CVSS3
4.6 Medium
CVSS2
Связанные уязвимости
In the Linux kernel, the following vulnerability has been resolved: usb: chipidea: udc: disconnect/reconnect from host when do suspend/resume Shawn and John reported a hang issue during system suspend as below: - USB gadget is enabled as Ethernet - There is data transfer over USB Ethernet (scp a big file between host and device) - Device is going in/out suspend (echo mem > /sys/power/state) The root cause is the USB device controller is suspended but the USB bus is still active which caused the USB host continues to transfer data with device and the device continues to queue USB requests (in this case, a delayed TCP ACK packet trigger the issue) after controller is suspended, however the USB controller clock is already gated off. Then if udc driver access registers after that point, the system will hang. The correct way to avoid such issue is to disconnect device from host when the USB bus is not at suspend state. Then the host will receive disconnect event and stop data transfer in...
In the Linux kernel, the following vulnerability has been resolved: usb: chipidea: udc: disconnect/reconnect from host when do suspend/resume Shawn and John reported a hang issue during system suspend as below: - USB gadget is enabled as Ethernet - There is data transfer over USB Ethernet (scp a big file between host and device) - Device is going in/out suspend (echo mem > /sys/power/state) The root cause is the USB device controller is suspended but the USB bus is still active which caused the USB host continues to transfer data with device and the device continues to queue USB requests (in this case, a delayed TCP ACK packet trigger the issue) after controller is suspended, however the USB controller clock is already gated off. Then if udc driver access registers after that point, the system will hang. The correct way to avoid such issue is to disconnect device from host when the USB bus is not at suspend state. Then the host will receive disconnect event and stop data transfer in...
In the Linux kernel, the following vulnerability has been resolved: usb: chipidea: udc: disconnect/reconnect from host when do suspend/resume Shawn and John reported a hang issue during system suspend as below: - USB gadget is enabled as Ethernet - There is data transfer over USB Ethernet (scp a big file between host and device) - Device is going in/out suspend (echo mem > /sys/power/state) The root cause is the USB device controller is suspended but the USB bus is still active which caused the USB host continues to transfer data with device and the device continues to queue USB requests (in this case, a delayed TCP ACK packet trigger the issue) after controller is suspended, however the USB controller clock is already gated off. Then if udc driver access registers after that point, the system will hang. The correct way to avoid such issue is to disconnect device from host when the USB bus is not at suspend state. Then the host will
In the Linux kernel, the following vulnerability has been resolved: u ...
In the Linux kernel, the following vulnerability has been resolved: usb: chipidea: udc: disconnect/reconnect from host when do suspend/resume Shawn and John reported a hang issue during system suspend as below: - USB gadget is enabled as Ethernet - There is data transfer over USB Ethernet (scp a big file between host and device) - Device is going in/out suspend (echo mem > /sys/power/state) The root cause is the USB device controller is suspended but the USB bus is still active which caused the USB host continues to transfer data with device and the device continues to queue USB requests (in this case, a delayed TCP ACK packet trigger the issue) after controller is suspended, however the USB controller clock is already gated off. Then if udc driver access registers after that point, the system will hang. The correct way to avoid such issue is to disconnect device from host when the USB bus is not at suspend state. Then the host wi...
EPSS
5.5 Medium
CVSS3
4.6 Medium
CVSS2