Логотип exploitDog
Консоль
Логотип exploitDog

exploitDog

fstec логотип

BDU:2026-04493

Опубликовано: 31 авг. 2025
Источник: fstec
CVSS3: 5.5
CVSS2: 4.6
EPSS Низкий

Описание

Уязвимость функции rtl9300_i2c_config_xfer() модуля drivers/i2c/busses/i2c-rtl9300.c драйвера аппаратной шины I2C ядра операционной системы Linux связана с отсутствием инициализации переменных. Эксплуатация уязвимости может позволить нарушителю вызвать отказ в обслуживании

Вендор

Сообщество свободного программного обеспечения

Наименование ПО

Linux

Версия ПО

от 6.13 до 6.16.7 включительно (Linux)

Тип ПО

Операционная система

Операционные системы и аппаратные платформы

Сообщество свободного программного обеспечения Linux от 6.13 до 6.16.7 включительно

Уровень опасности уязвимости

Средний уровень опасности (базовая оценка CVSS 2.0 составляет 4,6)
Средний уровень опасности (базовая оценка CVSS 3.1 составляет 5,5)

Возможные меры по устранению уязвимости

В условиях отсутствия обновлений безопасности от производителя рекомендуется придерживаться "Рекомендаций по безопасной настройке операционных систем LINUX", изложенных в методическом документе ФСТЭК России, утверждённом 25 декабря 2022 года.
Использование рекомендаций:
Для Linux:
https://git.kernel.org/stable/c/c91382328fc89f73144d5582f2d8f1dd3e41c8f7
https://git.kernel.org/linus/06418cb5a1a542a003fdb4ad8e76ea542d57cfba
https://kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.16.8

Статус уязвимости

Подтверждена производителем

Наличие эксплойта

Данные уточняются

Информация об устранении

Уязвимость устранена

Идентификаторы других систем описаний уязвимостей

EPSS

Процентиль: 5%
0.00018
Низкий

5.5 Medium

CVSS3

4.6 Medium

CVSS2

Связанные уязвимости

CVSS3: 5.5
ubuntu
7 месяцев назад

In the Linux kernel, the following vulnerability has been resolved: i2c: rtl9300: ensure data length is within supported range Add an explicit check for the xfer length to 'rtl9300_i2c_config_xfer' to ensure the data length isn't within the supported range. In particular a data length of 0 is not supported by the hardware and causes unintended or destructive behaviour. This limitation becomes obvious when looking at the register documentation [1]. 4 bits are reserved for DATA_WIDTH and the value of these 4 bits is used as N + 1, allowing a data length range of 1 <= len <= 16. Affected by this is the SMBus Quick Operation which works with a data length of 0. Passing 0 as the length causes an underflow of the value due to: (len - 1) & 0xf and effectively specifying a transfer length of 16 via the registers. This causes a 16-byte write operation instead of a Quick Write. For example, on SFP modules without write-protected EEPROM this soft-bricks them by overwriting some initial bytes. ...

redhat
7 месяцев назад

In the Linux kernel, the following vulnerability has been resolved: i2c: rtl9300: ensure data length is within supported range Add an explicit check for the xfer length to 'rtl9300_i2c_config_xfer' to ensure the data length isn't within the supported range. In particular a data length of 0 is not supported by the hardware and causes unintended or destructive behaviour. This limitation becomes obvious when looking at the register documentation [1]. 4 bits are reserved for DATA_WIDTH and the value of these 4 bits is used as N + 1, allowing a data length range of 1 <= len <= 16. Affected by this is the SMBus Quick Operation which works with a data length of 0. Passing 0 as the length causes an underflow of the value due to: (len - 1) & 0xf and effectively specifying a transfer length of 16 via the registers. This causes a 16-byte write operation instead of a Quick Write. For example, on SFP modules without write-protected EEPROM this soft-bricks them by overwriting some initial bytes. ...

CVSS3: 5.5
nvd
7 месяцев назад

In the Linux kernel, the following vulnerability has been resolved: i2c: rtl9300: ensure data length is within supported range Add an explicit check for the xfer length to 'rtl9300_i2c_config_xfer' to ensure the data length isn't within the supported range. In particular a data length of 0 is not supported by the hardware and causes unintended or destructive behaviour. This limitation becomes obvious when looking at the register documentation [1]. 4 bits are reserved for DATA_WIDTH and the value of these 4 bits is used as N + 1, allowing a data length range of 1 <= len <= 16. Affected by this is the SMBus Quick Operation which works with a data length of 0. Passing 0 as the length causes an underflow of the value due to: (len - 1) & 0xf and effectively specifying a transfer length of 16 via the registers. This causes a 16-byte write operation instead of a Quick Write. For example, on SFP modules without write-protected EEPROM this soft-bricks them by overwriting some initial byte

CVSS3: 5.5
debian
7 месяцев назад

In the Linux kernel, the following vulnerability has been resolved: i ...

CVSS3: 5.5
github
7 месяцев назад

In the Linux kernel, the following vulnerability has been resolved: i2c: rtl9300: ensure data length is within supported range Add an explicit check for the xfer length to 'rtl9300_i2c_config_xfer' to ensure the data length isn't within the supported range. In particular a data length of 0 is not supported by the hardware and causes unintended or destructive behaviour. This limitation becomes obvious when looking at the register documentation [1]. 4 bits are reserved for DATA_WIDTH and the value of these 4 bits is used as N + 1, allowing a data length range of 1 <= len <= 16. Affected by this is the SMBus Quick Operation which works with a data length of 0. Passing 0 as the length causes an underflow of the value due to: (len - 1) & 0xf and effectively specifying a transfer length of 16 via the registers. This causes a 16-byte write operation instead of a Quick Write. For example, on SFP modules without write-protected EEPROM this soft-bricks them by overwriting some initial b...

EPSS

Процентиль: 5%
0.00018
Низкий

5.5 Medium

CVSS3

4.6 Medium

CVSS2