Логотип exploitDog
Консоль
Логотип exploitDog

exploitDog

msrc логотип

CVE-2026-46148

Опубликовано: 02 июн. 2026
Источник: msrc
CVSS3: 5.5
EPSS Низкий

Описание

spi: microchip-core-qspi: control built-in cs manually

EPSS

Процентиль: 2%
0.00121
Низкий

5.5 Medium

CVSS3

Связанные уязвимости

CVSS3: 5.5
ubuntu
2 месяца назад

In the Linux kernel, the following vulnerability has been resolved: spi: microchip-core-qspi: control built-in cs manually The coreQSPI IP supports only a single chip select, which is automagically operated by the hardware - set low when the transmit buffer first gets written to and set high when the number of bytes written to the TOTALBYTES field of the FRAMES register have been sent on the bus. Additional devices must use GPIOs for their chip selects. It was reported to me that if there are two devices attached to this QSPI controller that the in-built chip select is set low while linux tries to access the device attached to the GPIO. This went undetected as the boards that connected multiple devices to the SPI controller all exclusively used GPIOs for chip selects, not relying on the built-in chip select at all. It turns out that this was because the built-in chip select, when controlled automagically, is set low when active and high when inactive, thereby ruling out its use for ...

redhat
2 месяца назад

In the Linux kernel, the following vulnerability has been resolved: spi: microchip-core-qspi: control built-in cs manually The coreQSPI IP supports only a single chip select, which is automagically operated by the hardware - set low when the transmit buffer first gets written to and set high when the number of bytes written to the TOTALBYTES field of the FRAMES register have been sent on the bus. Additional devices must use GPIOs for their chip selects. It was reported to me that if there are two devices attached to this QSPI controller that the in-built chip select is set low while linux tries to access the device attached to the GPIO. This went undetected as the boards that connected multiple devices to the SPI controller all exclusively used GPIOs for chip selects, not relying on the built-in chip select at all. It turns out that this was because the built-in chip select, when controlled automagically, is set low when active and high when inactive, thereby ruling out its use for ...

CVSS3: 5.5
nvd
2 месяца назад

In the Linux kernel, the following vulnerability has been resolved: spi: microchip-core-qspi: control built-in cs manually The coreQSPI IP supports only a single chip select, which is automagically operated by the hardware - set low when the transmit buffer first gets written to and set high when the number of bytes written to the TOTALBYTES field of the FRAMES register have been sent on the bus. Additional devices must use GPIOs for their chip selects. It was reported to me that if there are two devices attached to this QSPI controller that the in-built chip select is set low while linux tries to access the device attached to the GPIO. This went undetected as the boards that connected multiple devices to the SPI controller all exclusively used GPIOs for chip selects, not relying on the built-in chip select at all. It turns out that this was because the built-in chip select, when controlled automagically, is set low when active and high when inactive, thereby ruling out its use for

CVSS3: 5.5
debian
2 месяца назад

In the Linux kernel, the following vulnerability has been resolved: s ...

CVSS3: 5.5
github
2 месяца назад

In the Linux kernel, the following vulnerability has been resolved: spi: microchip-core-qspi: control built-in cs manually The coreQSPI IP supports only a single chip select, which is automagically operated by the hardware - set low when the transmit buffer first gets written to and set high when the number of bytes written to the TOTALBYTES field of the FRAMES register have been sent on the bus. Additional devices must use GPIOs for their chip selects. It was reported to me that if there are two devices attached to this QSPI controller that the in-built chip select is set low while linux tries to access the device attached to the GPIO. This went undetected as the boards that connected multiple devices to the SPI controller all exclusively used GPIOs for chip selects, not relying on the built-in chip select at all. It turns out that this was because the built-in chip select, when controlled automagically, is set low when active and high when inactive, thereby ruling out its use f...

EPSS

Процентиль: 2%
0.00121
Низкий

5.5 Medium

CVSS3