Описание
In the Linux kernel, the following vulnerability has been resolved:
serial: 8250: Fix PM usage_count for console handover
When console is enabled, univ8250_console_setup() calls
serial8250_console_setup() before .dev is set to uart_port. Therefore,
it will not call pm_runtime_get_sync(). Later, when the actual driver
is going to take over univ8250_console_exit() is called. As .dev is
already set, serial8250_console_exit() makes pm_runtime_put_sync() call
with usage count being zero triggering PM usage count warning
(extra debug for univ8250_console_setup(), univ8250_console_exit(), and
serial8250_register_ports()):
[ 0.068987] univ8250_console_setup ttyS0 nodev
[ 0.499670] printk: console [ttyS0] enabled
[ 0.717955] printk: console [ttyS0] printing thread started
[ 1.960163] serial8250_register_ports assigned dev for ttyS0
[ 1.976830] printk: console [ttyS0] disabled
[ 1.976888] printk: console [ttyS0] printing thread stopped
[ 1.977073] univ8250_console_exit ttyS0 usage:0
[ 1.977075] serial8250 serial8250: Runtime PM usage count underflow!
[ 1.977429] dw-apb-uart.6: ttyS0 at MMIO 0x4010006000 (irq = 33, base_baud = 115200) is a 16550A
[ 1.977812] univ8250_console_setup ttyS0 usage:2
[ 1.978167] printk: console [ttyS0] printing thread started
[ 1.978203] printk: console [ttyS0] enabled
To fix the issue, call pm_runtime_get_sync() in
serial8250_register_ports() as soon as .dev is set for an uart_port
if it has console enabled.
This problem became apparent only recently because 82586a721595 ("PM:
runtime: Avoid device usage count underflows") added the warning
printout. I confirmed this problem also occurs with v5.18 (w/o the
warning printout, obviously).
A flaw in the Linux kernel's serial driver (specifically the 8250 driver) mishandles power management (PM) usage counts during console handover. This mismanagement can lead to inconsistencies in the system's power management state, potentially causing devices to remain active when they should be suspended or vice versa. Such behavior may result in increased power consumption or system instability.
Затронутые пакеты
| Платформа | Пакет | Состояние | Рекомендация | Релиз |
|---|---|---|---|---|
| Red Hat Enterprise Linux 10 | kernel | Not affected | ||
| Red Hat Enterprise Linux 6 | kernel | Not affected | ||
| Red Hat Enterprise Linux 7 | kernel | Out of support scope | ||
| Red Hat Enterprise Linux 7 | kernel-rt | Out of support scope | ||
| Red Hat Enterprise Linux 8 | kernel | Out of support scope | ||
| Red Hat Enterprise Linux 8 | kernel-rt | Out of support scope | ||
| Red Hat Enterprise Linux 9 | kernel | Affected | ||
| Red Hat Enterprise Linux 9 | kernel-rt | Affected |
Показывать по
Дополнительная информация
Статус:
3.3 Low
CVSS3
Связанные уязвимости
In the Linux kernel, the following vulnerability has been resolved: serial: 8250: Fix PM usage_count for console handover When console is enabled, univ8250_console_setup() calls serial8250_console_setup() before .dev is set to uart_port. Therefore, it will not call pm_runtime_get_sync(). Later, when the actual driver is going to take over univ8250_console_exit() is called. As .dev is already set, serial8250_console_exit() makes pm_runtime_put_sync() call with usage count being zero triggering PM usage count warning (extra debug for univ8250_console_setup(), univ8250_console_exit(), and serial8250_register_ports()): [ 0.068987] univ8250_console_setup ttyS0 nodev [ 0.499670] printk: console [ttyS0] enabled [ 0.717955] printk: console [ttyS0] printing thread started [ 1.960163] serial8250_register_ports assigned dev for ttyS0 [ 1.976830] printk: console [ttyS0] disabled [ 1.976888] printk: console [ttyS0] printing thread stopped [ 1.977073] univ8250_console_exit tt...
In the Linux kernel, the following vulnerability has been resolved: serial: 8250: Fix PM usage_count for console handover When console is enabled, univ8250_console_setup() calls serial8250_console_setup() before .dev is set to uart_port. Therefore, it will not call pm_runtime_get_sync(). Later, when the actual driver is going to take over univ8250_console_exit() is called. As .dev is already set, serial8250_console_exit() makes pm_runtime_put_sync() call with usage count being zero triggering PM usage count warning (extra debug for univ8250_console_setup(), univ8250_console_exit(), and serial8250_register_ports()): [ 0.068987] univ8250_console_setup ttyS0 nodev [ 0.499670] printk: console [ttyS0] enabled [ 0.717955] printk: console [ttyS0] printing thread started [ 1.960163] serial8250_register_ports assigned dev for ttyS0 [ 1.976830] printk: console [ttyS0] disabled [ 1.976888] printk: console [ttyS0] printing thread stopped [ 1.977073] univ8250_console_exit tt
In the Linux kernel, the following vulnerability has been resolved: s ...
In the Linux kernel, the following vulnerability has been resolved: serial: 8250: Fix PM usage_count for console handover When console is enabled, univ8250_console_setup() calls serial8250_console_setup() before .dev is set to uart_port. Therefore, it will not call pm_runtime_get_sync(). Later, when the actual driver is going to take over univ8250_console_exit() is called. As .dev is already set, serial8250_console_exit() makes pm_runtime_put_sync() call with usage count being zero triggering PM usage count warning (extra debug for univ8250_console_setup(), univ8250_console_exit(), and serial8250_register_ports()): [ 0.068987] univ8250_console_setup ttyS0 nodev [ 0.499670] printk: console [ttyS0] enabled [ 0.717955] printk: console [ttyS0] printing thread started [ 1.960163] serial8250_register_ports assigned dev for ttyS0 [ 1.976830] printk: console [ttyS0] disabled [ 1.976888] printk: console [ttyS0] printing thread stopped [ 1.977073] univ8250_console_exit...
Уязвимость функции serial8250_register_ports() модуля drivers/tty/serial/8250/8250_core.c драйвера поддержки консоли TTY на последовательном порте ядра операционной системы Linux, позволяющая нарушителю вызвать отказ в обслуживании
3.3 Low
CVSS3