Описание
In the Linux kernel, the following vulnerability has been resolved:
usb: dwc3: Wait unconditionally after issuing EndXfer command
Currently all controller IP/revisions except DWC3_usb3 >= 310a
wait 1ms unconditionally for ENDXFER completion when IOC is not
set. This is because DWC_usb3 controller revisions >= 3.10a
supports GUCTL2[14: Rst_actbitlater] bit which allows polling
CMDACT bit to know whether ENDXFER command is completed.
Consider a case where an IN request was queued, and parallelly
soft_disconnect was called (due to ffs_epfile_release). This
eventually calls stop_active_transfer with IOC cleared, hence
send_gadget_ep_cmd() skips waiting for CMDACT cleared during
EndXfer. For DWC3 controllers with revisions >= 310a, we don't
forcefully wait for 1ms either, and we proceed by unmapping the
requests. If ENDXFER didn't complete by this time, it leads to
SMMU faults since the controller would still be accessing those
requests.
Fix this by ensuring ENDXFER completion by adding 1ms delay in
__dwc3_stop_active_transfer() unconditionally.
A flaw was found in the Linux kernel's USB DWC3 driver. A local attacker can cause a Denial of Service (DoS) by triggering a race condition during USB endpoint disconnection. When an active data transfer is cancelled, memory buffers may be unmapped while the hardware controller is still accessing them, causing memory management faults and resulting in a system crash.
Отчет
This vulnerability is rated as Low severity because it requires local access and is restricted to systems utilizing specific Synopsys DesignWare USB3 controller hardware operating in device or gadget mode, limiting the blast radius to a denial of service. Standard Red Hat Enterprise Linux enterprise deployments rarely utilize USB gadget functionality or the affected controller revisions, requiring specialized hardware configurations and elevated privileges to interact with the relevant endpoint interfaces. Consequently, the risk of an unprivileged local attacker triggering an SMMU fault or system crash under default production environments remains minimal.
Затронутые пакеты
| Платформа | Пакет | Состояние | Рекомендация | Релиз |
|---|---|---|---|---|
| Red Hat Enterprise Linux 6 | kernel | Not affected | ||
| Red Hat Enterprise Linux 7 | kernel | Not affected | ||
| Red Hat Enterprise Linux 7 | kernel-rt | Not affected | ||
| Red Hat Enterprise Linux 8 | kernel | Not affected | ||
| Red Hat Enterprise Linux 8 | kernel-rt | Not affected | ||
| Red Hat Enterprise Linux 9 | kernel-rt | Affected | ||
| Red Hat Enterprise Linux 9 | kernel | Fixed | RHSA-2024:9315 | 12.11.2024 |
| Red Hat Enterprise Linux 9 | kernel | Fixed | RHSA-2024:9315 | 12.11.2024 |
Показывать по
Дополнительная информация
Статус:
EPSS
4.4 Medium
CVSS3
Связанные уязвимости
In the Linux kernel, the following vulnerability has been resolved: usb: dwc3: Wait unconditionally after issuing EndXfer command Currently all controller IP/revisions except DWC3_usb3 >= 310a wait 1ms unconditionally for ENDXFER completion when IOC is not set. This is because DWC_usb3 controller revisions >= 3.10a supports GUCTL2[14: Rst_actbitlater] bit which allows polling CMDACT bit to know whether ENDXFER command is completed. Consider a case where an IN request was queued, and parallelly soft_disconnect was called (due to ffs_epfile_release). This eventually calls stop_active_transfer with IOC cleared, hence send_gadget_ep_cmd() skips waiting for CMDACT cleared during EndXfer. For DWC3 controllers with revisions >= 310a, we don't forcefully wait for 1ms either, and we proceed by unmapping the requests. If ENDXFER didn't complete by this time, it leads to SMMU faults since the controller would still be accessing those requests. Fix this by ensuring ENDXFER completion by adding ...
In the Linux kernel, the following vulnerability has been resolved: usb: dwc3: Wait unconditionally after issuing EndXfer command Currently all controller IP/revisions except DWC3_usb3 >= 310a wait 1ms unconditionally for ENDXFER completion when IOC is not set. This is because DWC_usb3 controller revisions >= 3.10a supports GUCTL2[14: Rst_actbitlater] bit which allows polling CMDACT bit to know whether ENDXFER command is completed. Consider a case where an IN request was queued, and parallelly soft_disconnect was called (due to ffs_epfile_release). This eventually calls stop_active_transfer with IOC cleared, hence send_gadget_ep_cmd() skips waiting for CMDACT cleared during EndXfer. For DWC3 controllers with revisions >= 310a, we don't forcefully wait for 1ms either, and we proceed by unmapping the requests. If ENDXFER didn't complete by this time, it leads to SMMU faults since the controller would still be accessing those requests. Fix this by ensuring ENDXFER completion by adding
In the Linux kernel, the following vulnerability has been resolved: u ...
In the Linux kernel, the following vulnerability has been resolved: usb: dwc3: Wait unconditionally after issuing EndXfer command Currently all controller IP/revisions except DWC3_usb3 >= 310a wait 1ms unconditionally for ENDXFER completion when IOC is not set. This is because DWC_usb3 controller revisions >= 3.10a supports GUCTL2[14: Rst_actbitlater] bit which allows polling CMDACT bit to know whether ENDXFER command is completed. Consider a case where an IN request was queued, and parallelly soft_disconnect was called (due to ffs_epfile_release). This eventually calls stop_active_transfer with IOC cleared, hence send_gadget_ep_cmd() skips waiting for CMDACT cleared during EndXfer. For DWC3 controllers with revisions >= 310a, we don't forcefully wait for 1ms either, and we proceed by unmapping the requests. If ENDXFER didn't complete by this time, it leads to SMMU faults since the controller would still be accessing those requests. Fix this by ensuring ENDXFER completion by add...
Уязвимость функции __dwc3_stop_active_transfer() драйвера DesignWare USB3 ядра операционной системы Linux, позволяющая нарушителю оказать воздействие на доступность защищаемой информации
EPSS
4.4 Medium
CVSS3