Описание
In the Linux kernel, the following vulnerability has been resolved:
drm/i915/dmc: Fix an unlikely NULL pointer deference at probe
intel_dmc_update_dc6_allowed_count() oopses when DMC hasn't been
initialized, and dmc is thus NULL.
That would be the case when the call path is
intel_power_domains_init_hw() -> {skl,bxt,icl}_display_core_init() ->
gen9_set_dc_state() -> intel_dmc_update_dc6_allowed_count(), as
intel_power_domains_init_hw() is called before intel_dmc_init().
However, gen9_set_dc_state() calls intel_dmc_update_dc6_allowed_count()
conditionally, depending on the current and target DC states. At probe,
the target is disabled, but if DC6 is enabled, the function is called,
and an oops follows. Apparently it's quite unlikely that DC6 is enabled
at probe, as we haven't seen this failure mode before.
It is also strange to have DC6 enabled at boot, since that would require
the DMC firmware (loaded by BIOS); the BIOS loading the DMC firmware and
the driver stopping / reprogramming the firmware is a poorly specified
sequence and as such unlikely an intentional BIOS behaviour. It's more
likely that BIOS is leaving an unintentionally enabled DC6 HW state
behind (without actually loading the required DMC firmware for this).
The tracking of the DC6 allowed counter only works if starting /
stopping the counter depends on the SW DC6 state vs. the current HW
DC6 state (since stopping the counter requires the DC5 counter captured
when the counter was started). Thus, using the HW DC6 state is incorrect
and it also leads to the above oops. Fix both issues by using the SW DC6
state for the tracking.
This is v2 of the fix originally sent by Jani, updated based on the
first Link: discussion below.
(cherry picked from commit 2344b93af8eb5da5d496b4e0529d35f0f559eaf0)
A flaw was found in the Linux kernel's drm/i915/dmc driver. Under specific, unlikely conditions during system startup, an uninitialized component can be accessed, leading to a null pointer dereference. This can be triggered if the Display Controller 6 (DC6) hardware state is unintentionally enabled at boot. A local attacker could potentially exploit this vulnerability to cause a system crash, resulting in a Denial of Service (DoS).
Затронутые пакеты
| Платформа | Пакет | Состояние | Рекомендация | Релиз |
|---|---|---|---|---|
| Red Hat Enterprise Linux 10 | kernel | Fix deferred | ||
| Red Hat Enterprise Linux 6 | kernel | Out of support scope | ||
| Red Hat Enterprise Linux 7 | kernel | Not affected | ||
| Red Hat Enterprise Linux 7 | kernel-rt | Not affected | ||
| Red Hat Enterprise Linux 8 | kernel | Not affected | ||
| Red Hat Enterprise Linux 8 | kernel-rt | Not affected | ||
| Red Hat Enterprise Linux 9 | kernel | Fix deferred | ||
| Red Hat Enterprise Linux 9 | kernel-rt | Fix deferred |
Показывать по
Дополнительная информация
Статус:
5.5 Medium
CVSS3
Связанные уязвимости
In the Linux kernel, the following vulnerability has been resolved: drm/i915/dmc: Fix an unlikely NULL pointer deference at probe intel_dmc_update_dc6_allowed_count() oopses when DMC hasn't been initialized, and dmc is thus NULL. That would be the case when the call path is intel_power_domains_init_hw() -> {skl,bxt,icl}_display_core_init() -> gen9_set_dc_state() -> intel_dmc_update_dc6_allowed_count(), as intel_power_domains_init_hw() is called *before* intel_dmc_init(). However, gen9_set_dc_state() calls intel_dmc_update_dc6_allowed_count() conditionally, depending on the current and target DC states. At probe, the target is disabled, but if DC6 is enabled, the function is called, and an oops follows. Apparently it's quite unlikely that DC6 is enabled at probe, as we haven't seen this failure mode before. It is also strange to have DC6 enabled at boot, since that would require the DMC firmware (loaded by BIOS); the BIOS loading the DMC firmware and the driver stopping / reprogrammi...
In the Linux kernel, the following vulnerability has been resolved: drm/i915/dmc: Fix an unlikely NULL pointer deference at probe intel_dmc_update_dc6_allowed_count() oopses when DMC hasn't been initialized, and dmc is thus NULL. That would be the case when the call path is intel_power_domains_init_hw() -> {skl,bxt,icl}_display_core_init() -> gen9_set_dc_state() -> intel_dmc_update_dc6_allowed_count(), as intel_power_domains_init_hw() is called *before* intel_dmc_init(). However, gen9_set_dc_state() calls intel_dmc_update_dc6_allowed_count() conditionally, depending on the current and target DC states. At probe, the target is disabled, but if DC6 is enabled, the function is called, and an oops follows. Apparently it's quite unlikely that DC6 is enabled at probe, as we haven't seen this failure mode before. It is also strange to have DC6 enabled at boot, since that would require the DMC firmware (loaded by BIOS); the BIOS loading the DMC firmware and the driver stopping / reprogram
In the Linux kernel, the following vulnerability has been resolved: d ...
In the Linux kernel, the following vulnerability has been resolved: drm/i915/dmc: Fix an unlikely NULL pointer deference at probe intel_dmc_update_dc6_allowed_count() oopses when DMC hasn't been initialized, and dmc is thus NULL. That would be the case when the call path is intel_power_domains_init_hw() -> {skl,bxt,icl}_display_core_init() -> gen9_set_dc_state() -> intel_dmc_update_dc6_allowed_count(), as intel_power_domains_init_hw() is called *before* intel_dmc_init(). However, gen9_set_dc_state() calls intel_dmc_update_dc6_allowed_count() conditionally, depending on the current and target DC states. At probe, the target is disabled, but if DC6 is enabled, the function is called, and an oops follows. Apparently it's quite unlikely that DC6 is enabled at probe, as we haven't seen this failure mode before. It is also strange to have DC6 enabled at boot, since that would require the DMC firmware (loaded by BIOS); the BIOS loading the DMC firmware and the driver stopping / reprog...
5.5 Medium
CVSS3