Описание
In the Linux kernel, the following vulnerability has been resolved:
comedi: dt2815: add hardware detection to prevent crash
The dt2815 driver crashes when attached to I/O ports without actual
hardware present. This occurs because syzkaller or users can attach
the driver to arbitrary I/O addresses via COMEDI_DEVCONFIG ioctl.
When no hardware exists at the specified port, inb() operations return
0xff (floating bus), but outb() operations can trigger page faults due
to undefined behavior, especially under race conditions:
BUG: unable to handle page fault for address: 000000007fffff90
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
RIP: 0010:dt2815_attach+0x6e0/0x1110
Add hardware detection by reading the status register before attempting
any write operations. If the read returns 0xff, assume no hardware is
present and fail the attach with -ENODEV. This prevents crashes from
outb() operations on non-existent hardware.
A flaw was found in the Linux kernel's comedi dt2815 driver. A local user can exploit this vulnerability by attaching the driver to arbitrary I/O addresses without actual hardware present. This can trigger a page fault during output operations on non-existent hardware, leading to a kernel crash. This issue results in a denial of service.
Затронутые пакеты
| Платформа | Пакет | Состояние | Рекомендация | Релиз |
|---|---|---|---|---|
| Red Hat Enterprise Linux 10 | kernel | Not affected | ||
| Red Hat Enterprise Linux 6 | kernel | Not affected | ||
| Red Hat Enterprise Linux 7 | kernel | Not affected | ||
| Red Hat Enterprise Linux 7 | kernel-rt | Not affected | ||
| Red Hat Enterprise Linux 8 | kernel | Not affected | ||
| Red Hat Enterprise Linux 8 | kernel-rt | Not affected | ||
| Red Hat Enterprise Linux 9 | kernel | Not affected | ||
| Red Hat Enterprise Linux 9 | kernel-rt | Not affected |
Показывать по
Дополнительная информация
EPSS
Связанные уязвимости
In the Linux kernel, the following vulnerability has been resolved: comedi: dt2815: add hardware detection to prevent crash The dt2815 driver crashes when attached to I/O ports without actual hardware present. This occurs because syzkaller or users can attach the driver to arbitrary I/O addresses via COMEDI_DEVCONFIG ioctl. When no hardware exists at the specified port, inb() operations return 0xff (floating bus), but outb() operations can trigger page faults due to undefined behavior, especially under race conditions: BUG: unable to handle page fault for address: 000000007fffff90 #PF: supervisor write access in kernel mode #PF: error_code(0x0002) - not-present page RIP: 0010:dt2815_attach+0x6e0/0x1110 Add hardware detection by reading the status register before attempting any write operations. If the read returns 0xff, assume no hardware is present and fail the attach with -ENODEV. This prevents crashes from outb() operations on non-existent hardware.
In the Linux kernel, the following vulnerability has been resolved: comedi: dt2815: add hardware detection to prevent crash The dt2815 driver crashes when attached to I/O ports without actual hardware present. This occurs because syzkaller or users can attach the driver to arbitrary I/O addresses via COMEDI_DEVCONFIG ioctl. When no hardware exists at the specified port, inb() operations return 0xff (floating bus), but outb() operations can trigger page faults due to undefined behavior, especially under race conditions: BUG: unable to handle page fault for address: 000000007fffff90 #PF: supervisor write access in kernel mode #PF: error_code(0x0002) - not-present page RIP: 0010:dt2815_attach+0x6e0/0x1110 Add hardware detection by reading the status register before attempting any write operations. If the read returns 0xff, assume no hardware is present and fail the attach with -ENODEV. This prevents crashes from outb() operations on non-existent hardware.
In the Linux kernel, the following vulnerability has been resolved: c ...
In the Linux kernel, the following vulnerability has been resolved: comedi: dt2815: add hardware detection to prevent crash The dt2815 driver crashes when attached to I/O ports without actual hardware present. This occurs because syzkaller or users can attach the driver to arbitrary I/O addresses via COMEDI_DEVCONFIG ioctl. When no hardware exists at the specified port, inb() operations return 0xff (floating bus), but outb() operations can trigger page faults due to undefined behavior, especially under race conditions: BUG: unable to handle page fault for address: 000000007fffff90 #PF: supervisor write access in kernel mode #PF: error_code(0x0002) - not-present page RIP: 0010:dt2815_attach+0x6e0/0x1110 Add hardware detection by reading the status register before attempting any write operations. If the read returns 0xff, assume no hardware is present and fail the attach with -ENODEV. This prevents crashes from outb() operations on non-existent hardware.
EPSS