Описание
In the Linux kernel, the following vulnerability has been resolved:
dpaa2-switch: validate num_ifs to prevent out-of-bounds write
The driver obtains sw_attr.num_ifs from firmware via dpsw_get_attributes()
but never validates it against DPSW_MAX_IF (64). This value controls
iteration in dpaa2_switch_fdb_get_flood_cfg(), which writes port indices
into the fixed-size cfg->if_id[DPSW_MAX_IF] array. When firmware reports
num_ifs >= 64, the loop can write past the array bounds.
Add a bound check for num_ifs in dpaa2_switch_init().
dpaa2_switch_fdb_get_flood_cfg() appends the control interface (port
num_ifs) after all matched ports. When num_ifs == DPSW_MAX_IF and all
ports match the flood filter, the loop fills all 64 slots and the control
interface write overflows by one entry.
The check uses >= because num_ifs == DPSW_MAX_IF is also functionally
broken.
build_if_id_bitmap() silently drops any ID >= 64:
if (id[i] < DPSW_MAX_IF)
bmap[id[i] / 64] |= ...
A flaw was found in the Linux kernel dpaa2-switch driver. This out-of-bounds write vulnerability occurs because the driver does not validate the num_ifs value reported by the firmware against the DPSW_MAX_IF limit. A highly privileged attacker, capable of influencing the DPAA2 firmware or management complex attributes, could exploit this to trigger kernel memory corruption through flood configuration handling.
Отчет
A flaw in the Linux kernel dpaa2-switch driver allows an out-of-bounds write when a firmware-reported num_ifs value is not validated against DPSW_MAX_IF. A highly privileged attacker able to influence the DPAA2 firmware or management complex attributes could trigger kernel memory corruption through flood configuration handling. For the CVSS the PR:H is used because the vulnerable value originates from firmware/device attributes rather than from an unprivileged local or remote user-controlled input.
Меры по смягчению последствий
To mitigate this issue, prevent module fsl-dpaa2-eth from being loaded. Please see https://access.redhat.com/solutions/41278 for how to blacklist a kernel module to prevent it from loading automatically.
Затронутые пакеты
| Платформа | Пакет | Состояние | Рекомендация | Релиз |
|---|---|---|---|---|
| Red Hat Enterprise Linux 6 | kernel | Not affected | ||
| Red Hat Enterprise Linux 7 | kernel | Not affected | ||
| Red Hat Enterprise Linux 7 | kernel-rt | Not affected | ||
| Red Hat Enterprise Linux 8 | kernel | Not affected | ||
| Red Hat Enterprise Linux 8 | kernel-rt | Not affected | ||
| Red Hat Enterprise Linux 9 | kernel | Not affected | ||
| Red Hat Enterprise Linux 9 | kernel-rt | Not affected | ||
| Red Hat Enterprise Linux 10 | kernel | Fixed | RHSA-2026:21557 | 28.05.2026 |
Показывать по
Дополнительная информация
Статус:
EPSS
6.7 Medium
CVSS3
Связанные уязвимости
In the Linux kernel, the following vulnerability has been resolved: dpaa2-switch: validate num_ifs to prevent out-of-bounds write The driver obtains sw_attr.num_ifs from firmware via dpsw_get_attributes() but never validates it against DPSW_MAX_IF (64). This value controls iteration in dpaa2_switch_fdb_get_flood_cfg(), which writes port indices into the fixed-size cfg->if_id[DPSW_MAX_IF] array. When firmware reports num_ifs >= 64, the loop can write past the array bounds. Add a bound check for num_ifs in dpaa2_switch_init(). dpaa2_switch_fdb_get_flood_cfg() appends the control interface (port num_ifs) after all matched ports. When num_ifs == DPSW_MAX_IF and all ports match the flood filter, the loop fills all 64 slots and the control interface write overflows by one entry. The check uses >= because num_ifs == DPSW_MAX_IF is also functionally broken. build_if_id_bitmap() silently drops any ID >= 64: if (id[i] < DPSW_MAX_IF) bmap[id[i] / 64] |= ...
In the Linux kernel, the following vulnerability has been resolved: dpaa2-switch: validate num_ifs to prevent out-of-bounds write The driver obtains sw_attr.num_ifs from firmware via dpsw_get_attributes() but never validates it against DPSW_MAX_IF (64). This value controls iteration in dpaa2_switch_fdb_get_flood_cfg(), which writes port indices into the fixed-size cfg->if_id[DPSW_MAX_IF] array. When firmware reports num_ifs >= 64, the loop can write past the array bounds. Add a bound check for num_ifs in dpaa2_switch_init(). dpaa2_switch_fdb_get_flood_cfg() appends the control interface (port num_ifs) after all matched ports. When num_ifs == DPSW_MAX_IF and all ports match the flood filter, the loop fills all 64 slots and the control interface write overflows by one entry. The check uses >= because num_ifs == DPSW_MAX_IF is also functionally broken. build_if_id_bitmap() silently drops any ID >= 64: if (id[i] < DPSW_MAX_IF) bmap[id[i] / 64] |= ...
In the Linux kernel, the following vulnerability has been resolved: d ...
In the Linux kernel, the following vulnerability has been resolved: dpaa2-switch: validate num_ifs to prevent out-of-bounds write The driver obtains sw_attr.num_ifs from firmware via dpsw_get_attributes() but never validates it against DPSW_MAX_IF (64). This value controls iteration in dpaa2_switch_fdb_get_flood_cfg(), which writes port indices into the fixed-size cfg->if_id[DPSW_MAX_IF] array. When firmware reports num_ifs >= 64, the loop can write past the array bounds. Add a bound check for num_ifs in dpaa2_switch_init(). dpaa2_switch_fdb_get_flood_cfg() appends the control interface (port num_ifs) after all matched ports. When num_ifs == DPSW_MAX_IF and all ports match the flood filter, the loop fills all 64 slots and the control interface write overflows by one entry. The check uses >= because num_ifs == DPSW_MAX_IF is also functionally broken. build_if_id_bitmap() silently drops any ID >= 64: if (id[i] < DPSW_MAX_IF) bmap[id[i] / 64] |= ...
EPSS
6.7 Medium
CVSS3