Описание
In the Linux kernel, the following vulnerability has been resolved:
x86/apic: Disable x2apic on resume if the kernel expects so
When resuming from s2ram, firmware may re-enable x2apic mode, which may have
been disabled by the kernel during boot either because it doesn't support IRQ
remapping or for other reasons. This causes the kernel to continue using the
xapic interface, while the hardware is in x2apic mode, which causes hangs.
This happens on defconfig + bare metal + s2ram.
Fix this in lapic_resume() by disabling x2apic if the kernel expects it to be
disabled, i.e. when x2apic_mode = 0.
The ACPI v6.6 spec, Section 16.3 [1] says firmware restores either the
pre-sleep configuration or initial boot configuration for each CPU, including
MSR state:
When executing from the power-on reset vector as a result of waking from an
S2 or S3 sleep state, the platform firmware performs only the hardware
initialization required to restore the system to either the state the
platform was in prior to the initial operating system boot, or to the
pre-sleep configuration state. In multiprocessor systems, non-boot
processors should be placed in the same state as prior to the initial
operating system boot.
(further ahead)
If this is an S2 or S3 wake, then the platform runtime firmware restores
minimum context of the system before jumping to the waking vector. This
includes:
CPU configuration. Platform runtime firmware restores the pre-sleep
configuration or initial boot configuration of each CPU (MSR, MTRR,
firmware update, SMBase, and so on). Interrupts must be disabled (for
IA-32 processors, disabled by CLI instruction).
(and other things)
So at least as per the spec, re-enablement of x2apic by the firmware is
allowed if "x2apic on" is a part of the initial boot configuration.
[1] https://uefi.org/specs/ACPI/6.6/16_Waking_and_Sleeping.html#initialization
[ bp: Massage. ]
A flaw was found in the Linux kernel. When resuming from suspend to RAM (s2ram), the system's firmware may incorrectly re-enable x2apic mode, even if the kernel had previously disabled it. This mismatch causes the kernel to operate with an incompatible interface, leading to system hangs and a Denial of Service.
Отчет
This Moderate flaw in the Linux kernel can lead to a system hang, resulting in a denial of service. This occurs on x86 systems when resuming from suspend-to-RAM (s2ram) if the firmware re-enables x2apic mode while the kernel expects it to remain disabled. This mismatch in APIC mode configuration can render the system unresponsive.
Меры по смягчению последствий
Mitigation for this issue is either not available or the currently available options do not meet the Red Hat Product Security criteria comprising ease of use and deployment, applicability to widespread installation base, or stability.
Затронутые пакеты
| Платформа | Пакет | Состояние | Рекомендация | Релиз |
|---|---|---|---|---|
| Red Hat Enterprise Linux 10 | kernel | Fix deferred | ||
| Red Hat Enterprise Linux 6 | kernel | Out of support scope | ||
| Red Hat Enterprise Linux 7 | kernel | Fix deferred | ||
| Red Hat Enterprise Linux 7 | kernel-rt | Fix deferred | ||
| Red Hat Enterprise Linux 8 | kernel | Fix deferred | ||
| Red Hat Enterprise Linux 8 | kernel-rt | Fix deferred | ||
| Red Hat Enterprise Linux 9 | kernel | Fix deferred | ||
| Red Hat Enterprise Linux 9 | kernel-rt | Fix deferred |
Показывать по
Дополнительная информация
Статус:
EPSS
5.5 Medium
CVSS3
Связанные уязвимости
In the Linux kernel, the following vulnerability has been resolved: x86/apic: Disable x2apic on resume if the kernel expects so When resuming from s2ram, firmware may re-enable x2apic mode, which may have been disabled by the kernel during boot either because it doesn't support IRQ remapping or for other reasons. This causes the kernel to continue using the xapic interface, while the hardware is in x2apic mode, which causes hangs. This happens on defconfig + bare metal + s2ram. Fix this in lapic_resume() by disabling x2apic if the kernel expects it to be disabled, i.e. when x2apic_mode = 0. The ACPI v6.6 spec, Section 16.3 [1] says firmware restores either the pre-sleep configuration or initial boot configuration for each CPU, including MSR state: When executing from the power-on reset vector as a result of waking from an S2 or S3 sleep state, the platform firmware performs only the hardware initialization required to restore the system to either the state the platform was in prior ...
In the Linux kernel, the following vulnerability has been resolved: x86/apic: Disable x2apic on resume if the kernel expects so When resuming from s2ram, firmware may re-enable x2apic mode, which may have been disabled by the kernel during boot either because it doesn't support IRQ remapping or for other reasons. This causes the kernel to continue using the xapic interface, while the hardware is in x2apic mode, which causes hangs. This happens on defconfig + bare metal + s2ram. Fix this in lapic_resume() by disabling x2apic if the kernel expects it to be disabled, i.e. when x2apic_mode = 0. The ACPI v6.6 spec, Section 16.3 [1] says firmware restores either the pre-sleep configuration or initial boot configuration for each CPU, including MSR state: When executing from the power-on reset vector as a result of waking from an S2 or S3 sleep state, the platform firmware performs only the hardware initialization required to restore the system to either the state the platform was
In the Linux kernel, the following vulnerability has been resolved: x ...
In the Linux kernel, the following vulnerability has been resolved: x86/apic: Disable x2apic on resume if the kernel expects so When resuming from s2ram, firmware may re-enable x2apic mode, which may have been disabled by the kernel during boot either because it doesn't support IRQ remapping or for other reasons. This causes the kernel to continue using the xapic interface, while the hardware is in x2apic mode, which causes hangs. This happens on defconfig + bare metal + s2ram. Fix this in lapic_resume() by disabling x2apic if the kernel expects it to be disabled, i.e. when x2apic_mode = 0. The ACPI v6.6 spec, Section 16.3 [1] says firmware restores either the pre-sleep configuration or initial boot configuration for each CPU, including MSR state: When executing from the power-on reset vector as a result of waking from an S2 or S3 sleep state, the platform firmware performs only the hardware initialization required to restore the system to either the state the platform ...
ELSA-2026-50372: Unbreakable Enterprise kernel security update (IMPORTANT)
EPSS
5.5 Medium
CVSS3