Описание
In the Linux kernel, the following vulnerability has been resolved:
libceph: Use u32 for non-negative values in ceph_monmap_decode()
This patch fixes unnecessary implicit conversions that change signedness
of blob_len and num_mon in ceph_monmap_decode().
Currently blob_len and num_mon are (signed) int variables. They are used
to hold values that are always non-negative and get assigned in
ceph_decode_32_safe(), which is meant to assign u32 values. Both
variables are subsequently used as unsigned values, and the value of
num_mon is further assigned to monmap->num_mon, which is of type u32.
Therefore, both variables should be of type u32. This is especially
relevant for num_mon. If the value read from the incoming message is
very large, it is interpreted as a negative value, and the check for
num_mon > CEPH_MAX_MON does not catch it. This leads to the attempt to
allocate a very large chunk of memory for monmap, which will most likely
fail. In this case, an unnecessary attempt to allocate memory is
performed, and -ENOMEM is returned instead of -EINVAL.
A flaw was found in the libceph component of the Linux kernel. This vulnerability occurs in the ceph_monmap_decode() function due to incorrect handling of non-negative values, where int variables are used instead of u32 for blob_len and num_mon. An attacker could exploit this by sending a specially crafted message with an excessively large num_mon value. This could lead to an attempt to allocate a very large amount of memory, resulting in a Denial of Service (DoS) condition.
Отчет
Red Hat acknowledges the upstream Linux kernel correction for «libceph» as described in COMMENT_ZERO. Fixes are delivered through standard kernel errata for supported products. Operational exposure depends on whether this subsystem or driver is active in your configuration.
Меры по смягчению последствий
To mitigate this issue, prevent the ceph module from being loaded. See https://access.redhat.com/solutions/41278 for instructions.
Затронутые пакеты
| Платформа | Пакет | Состояние | Рекомендация | Релиз |
|---|---|---|---|---|
| Red Hat Enterprise Linux 10 | kernel | Fix deferred | ||
| Red Hat Enterprise Linux 6 | kernel | Not affected | ||
| Red Hat Enterprise Linux 7 | kernel | Fix deferred | ||
| Red Hat Enterprise Linux 7 | kernel-rt | Fix deferred | ||
| Red Hat Enterprise Linux 8 | kernel | Out of support scope | ||
| Red Hat Enterprise Linux 8 | kernel-rt | Fix deferred | ||
| Red Hat Enterprise Linux 9 | kernel | Fix deferred | ||
| Red Hat Enterprise Linux 9 | kernel-rt | Fix deferred |
Показывать по
Дополнительная информация
Статус:
5.5 Medium
CVSS3
Связанные уязвимости
In the Linux kernel, the following vulnerability has been resolved: libceph: Use u32 for non-negative values in ceph_monmap_decode() This patch fixes unnecessary implicit conversions that change signedness of blob_len and num_mon in ceph_monmap_decode(). Currently blob_len and num_mon are (signed) int variables. They are used to hold values that are always non-negative and get assigned in ceph_decode_32_safe(), which is meant to assign u32 values. Both variables are subsequently used as unsigned values, and the value of num_mon is further assigned to monmap->num_mon, which is of type u32. Therefore, both variables should be of type u32. This is especially relevant for num_mon. If the value read from the incoming message is very large, it is interpreted as a negative value, and the check for num_mon > CEPH_MAX_MON does not catch it. This leads to the attempt to allocate a very large chunk of memory for monmap, which will most likely fail. In this case, an unnecessary attempt to alloc...
In the Linux kernel, the following vulnerability has been resolved: libceph: Use u32 for non-negative values in ceph_monmap_decode() This patch fixes unnecessary implicit conversions that change signedness of blob_len and num_mon in ceph_monmap_decode(). Currently blob_len and num_mon are (signed) int variables. They are used to hold values that are always non-negative and get assigned in ceph_decode_32_safe(), which is meant to assign u32 values. Both variables are subsequently used as unsigned values, and the value of num_mon is further assigned to monmap->num_mon, which is of type u32. Therefore, both variables should be of type u32. This is especially relevant for num_mon. If the value read from the incoming message is very large, it is interpreted as a negative value, and the check for num_mon > CEPH_MAX_MON does not catch it. This leads to the attempt to allocate a very large chunk of memory for monmap, which will most likely fail. In this case, an unnecessary attempt to alloca
In the Linux kernel, the following vulnerability has been resolved: l ...
In the Linux kernel, the following vulnerability has been resolved: libceph: Use u32 for non-negative values in ceph_monmap_decode() This patch fixes unnecessary implicit conversions that change signedness of blob_len and num_mon in ceph_monmap_decode(). Currently blob_len and num_mon are (signed) int variables. They are used to hold values that are always non-negative and get assigned in ceph_decode_32_safe(), which is meant to assign u32 values. Both variables are subsequently used as unsigned values, and the value of num_mon is further assigned to monmap->num_mon, which is of type u32. Therefore, both variables should be of type u32. This is especially relevant for num_mon. If the value read from the incoming message is very large, it is interpreted as a negative value, and the check for num_mon > CEPH_MAX_MON does not catch it. This leads to the attempt to allocate a very large chunk of memory for monmap, which will most likely fail. In this case, an unnecessary attempt to all...
5.5 Medium
CVSS3