Описание
In the Linux kernel, the following vulnerability has been resolved:
irq_work: Fix use-after-free in irq_work_single() on PREEMPT_RT
On PREEMPT_RT, non-HARD irq_work runs in per-CPU kthreads via
run_irq_workd(), so irq_work_sync() uses rcuwait() to wait for BUSY==0.
After irq_work_single() clears BUSY via atomic_cmpxchg(), it still
dereferences @work for irq_work_is_hard() and rcuwait_wake_up().
An irq_work_sync() caller on another CPU that enters after BUSY is cleared
can observe BUSY==0 immediately, return, and free the work before those
accesses complete — causing a use-after-free.
Fix this by wrapping run_irq_workd() in guard(rcu)() so that the entire
irq_work_single() execution is within an RCU read-side critical
section. Then add synchronize_rcu() in irq_work_sync() after
rcuwait_wait_event() to ensure the caller waits for the RCU grace period
before returning, preventing premature frees.
A flaw was found in the Linux kernel, specifically within the irq_work subsystem when running on systems configured with PREEMPT_RT. This vulnerability is a use-after-free, where the system attempts to access memory after it has been released. A local attacker could exploit this timing issue to cause a system crash, leading to a denial of service. In some scenarios, this type of flaw could potentially be leveraged for arbitrary code execution.
Затронутые пакеты
| Платформа | Пакет | Состояние | Рекомендация | Релиз |
|---|---|---|---|---|
| Red Hat Enterprise Linux 10 | kernel | Fix deferred | ||
| Red Hat Enterprise Linux 6 | kernel | Not affected | ||
| Red Hat Enterprise Linux 7 | kernel | Not affected | ||
| Red Hat Enterprise Linux 7 | kernel-rt | Not affected | ||
| Red Hat Enterprise Linux 8 | kernel | Not affected | ||
| Red Hat Enterprise Linux 8 | kernel-rt | Not affected | ||
| Red Hat Enterprise Linux 9 | kernel | Fix deferred | ||
| Red Hat Enterprise Linux 9 | kernel-rt | Fix deferred |
Показывать по
Дополнительная информация
Статус:
EPSS
5.5 Medium
CVSS3
Связанные уязвимости
In the Linux kernel, the following vulnerability has been resolved: irq_work: Fix use-after-free in irq_work_single() on PREEMPT_RT On PREEMPT_RT, non-HARD irq_work runs in per-CPU kthreads via run_irq_workd(), so irq_work_sync() uses rcuwait() to wait for BUSY==0. After irq_work_single() clears BUSY via atomic_cmpxchg(), it still dereferences @work for irq_work_is_hard() and rcuwait_wake_up(). An irq_work_sync() caller on another CPU that enters after BUSY is cleared can observe BUSY==0 immediately, return, and free the work before those accesses complete — causing a use-after-free. Fix this by wrapping run_irq_workd() in guard(rcu)() so that the entire irq_work_single() execution is within an RCU read-side critical section. Then add synchronize_rcu() in irq_work_sync() after rcuwait_wait_event() to ensure the caller waits for the RCU grace period before returning, preventing premature frees.
In the Linux kernel, the following vulnerability has been resolved: irq_work: Fix use-after-free in irq_work_single() on PREEMPT_RT On PREEMPT_RT, non-HARD irq_work runs in per-CPU kthreads via run_irq_workd(), so irq_work_sync() uses rcuwait() to wait for BUSY==0. After irq_work_single() clears BUSY via atomic_cmpxchg(), it still dereferences @work for irq_work_is_hard() and rcuwait_wake_up(). An irq_work_sync() caller on another CPU that enters after BUSY is cleared can observe BUSY==0 immediately, return, and free the work before those accesses complete — causing a use-after-free. Fix this by wrapping run_irq_workd() in guard(rcu)() so that the entire irq_work_single() execution is within an RCU read-side critical section. Then add synchronize_rcu() in irq_work_sync() after rcuwait_wait_event() to ensure the caller waits for the RCU grace period before returning, preventing premature frees.
In the Linux kernel, the following vulnerability has been resolved: i ...
In the Linux kernel, the following vulnerability has been resolved: irq_work: Fix use-after-free in irq_work_single() on PREEMPT_RT On PREEMPT_RT, non-HARD irq_work runs in per-CPU kthreads via run_irq_workd(), so irq_work_sync() uses rcuwait() to wait for BUSY==0. After irq_work_single() clears BUSY via atomic_cmpxchg(), it still dereferences @work for irq_work_is_hard() and rcuwait_wake_up(). An irq_work_sync() caller on another CPU that enters after BUSY is cleared can observe BUSY==0 immediately, return, and free the work before those accesses complete — causing a use-after-free. Fix this by wrapping run_irq_workd() in guard(rcu)() so that the entire irq_work_single() execution is within an RCU read-side critical section. Then add synchronize_rcu() in irq_work_sync() after rcuwait_wait_event() to ensure the caller waits for the RCU grace period before returning, preventing premature frees.
EPSS
5.5 Medium
CVSS3