Описание
In the Linux kernel, the following vulnerability has been resolved:
can: bcm: fix stale rx/tx ops after device removal
RX: an RX_SETUP update(!) for an existing op skipped can_rx_register()
unconditionally, even when a concurrent NETDEV_UNREGISTER had already
torn down its registration (op->rx_reg_dev == NULL). This silently
did not re-enable frame delivery for that updated filter. bcm_rx_setup()
now re-registers in that case, while leaving rx_ops with ifindex = 0
(all CAN devices) which never carry a tracked rx_reg_dev registered as-is.
TX: bcm_notify() only handled bo->rx_ops on NETDEV_UNREGISTER, leaving
tx_ops with an active cyclic transmission re-arming its hrtimer
indefinitely to execute bcm_tx_timeout_handler(). Cancelling the hrtimer
prevents the runaway timer and any injection into a later reused ifindex,
since nothing else calls bcm_can_tx() for the op until an explicit
TX_SETUP update re-arms it.
Unlike bcm_rx_unreg(), which clears the tracked rx_reg_dev for rx_ops,
the ifindex is intentionally left unchanged for tx_ops. bcm_tx_setup()
always rejects ifindex 0, so clearing it would strand the op: neither a
later TX_SETUP (bcm_find_op()) nor TX_DELETE (bcm_delete_tx_op()) could
ever find it again, since both require an exact ifindex match.
A flaw was found in the Linux kernel's Broadcom Controller Area Network (CAN) bus driver. When a CAN device is removed, the driver may fail to properly manage its receive and transmit operations. This can lead to receive filters not being correctly re-enabled after updates, preventing expected data processing. Additionally, transmit timers might continue to run indefinitely, potentially causing system instability due to resource exhaustion or unintended data injection into a re-used network interface.
Затронутые пакеты
| Платформа | Пакет | Состояние | Рекомендация | Релиз |
|---|---|---|---|---|
| Red Hat Enterprise Linux 10 | kernel | Fix deferred | ||
| Red Hat Enterprise Linux 6 | kernel | Out of support scope | ||
| Red Hat Enterprise Linux 7 | kernel | Fix deferred | ||
| Red Hat Enterprise Linux 7 | kernel-rt | Fix deferred | ||
| Red Hat Enterprise Linux 8 | kernel | Fix deferred | ||
| Red Hat Enterprise Linux 8 | kernel-rt | Fix deferred | ||
| Red Hat Enterprise Linux 9 | kernel | Fix deferred | ||
| Red Hat Enterprise Linux 9 | kernel-rt | Fix deferred |
Показывать по
Дополнительная информация
Статус:
EPSS
5.5 Medium
CVSS3
Связанные уязвимости
In the Linux kernel, the following vulnerability has been resolved: can: bcm: fix stale rx/tx ops after device removal RX: an RX_SETUP update(!) for an existing op skipped can_rx_register() unconditionally, even when a concurrent NETDEV_UNREGISTER had already torn down its registration (op->rx_reg_dev == NULL). This silently did not re-enable frame delivery for that updated filter. bcm_rx_setup() now re-registers in that case, while leaving rx_ops with ifindex = 0 (all CAN devices) which never carry a tracked rx_reg_dev registered as-is. TX: bcm_notify() only handled bo->rx_ops on NETDEV_UNREGISTER, leaving tx_ops with an active cyclic transmission re-arming its hrtimer indefinitely to execute bcm_tx_timeout_handler(). Cancelling the hrtimer prevents the runaway timer and any injection into a later reused ifindex, since nothing else calls bcm_can_tx() for the op until an explicit TX_SETUP update re-arms it. Unlike bcm_rx_unreg(), which clears the tracked rx_reg_dev for rx_ops, the i...
In the Linux kernel, the following vulnerability has been resolved: can: bcm: fix stale rx/tx ops after device removal RX: an RX_SETUP update(!) for an existing op skipped can_rx_register() unconditionally, even when a concurrent NETDEV_UNREGISTER had already torn down its registration (op->rx_reg_dev == NULL). This silently did not re-enable frame delivery for that updated filter. bcm_rx_setup() now re-registers in that case, while leaving rx_ops with ifindex = 0 (all CAN devices) which never carry a tracked rx_reg_dev registered as-is. TX: bcm_notify() only handled bo->rx_ops on NETDEV_UNREGISTER, leaving tx_ops with an active cyclic transmission re-arming its hrtimer indefinitely to execute bcm_tx_timeout_handler(). Cancelling the hrtimer prevents the runaway timer and any injection into a later reused ifindex, since nothing else calls bcm_can_tx() for the op until an explicit TX_SETUP update re-arms it. Unlike bcm_rx_unreg(), which clears the tracked rx_reg_dev for rx_ops, the
In the Linux kernel, the following vulnerability has been resolved: c ...
In the Linux kernel, the following vulnerability has been resolved: can: bcm: fix stale rx/tx ops after device removal RX: an RX_SETUP update(!) for an existing op skipped can_rx_register() unconditionally, even when a concurrent NETDEV_UNREGISTER had already torn down its registration (op->rx_reg_dev == NULL). This silently did not re-enable frame delivery for that updated filter. bcm_rx_setup() now re-registers in that case, while leaving rx_ops with ifindex = 0 (all CAN devices) which never carry a tracked rx_reg_dev registered as-is. TX: bcm_notify() only handled bo->rx_ops on NETDEV_UNREGISTER, leaving tx_ops with an active cyclic transmission re-arming its hrtimer indefinitely to execute bcm_tx_timeout_handler(). Cancelling the hrtimer prevents the runaway timer and any injection into a later reused ifindex, since nothing else calls bcm_can_tx() for the op until an explicit TX_SETUP update re-arms it. Unlike bcm_rx_unreg(), which clears the tracked rx_reg_dev for rx_ops, t...
EPSS
5.5 Medium
CVSS3