Описание
In the Linux kernel, the following vulnerability has been resolved:
spi: xilinx: use FIFO occupancy register to determine buffer size
The method the driver uses to determine the size of the FIFO has a
problem. What it currently does is this:
It stops the SPI hardware and writes to the TX FIFO register until TX
FIFO FULL asserts in the status register. But the hardware does not only
have the FIFO, it also has a shift register which can hold a byte. This
can be seen, when writing a byte to the FIFO (while the SPI hardware is
stopped,) the TX FIFO EMPTY is still empty. So, if we have a FIFO size
of 16 for example, the current method returns a 17.
This is a problem, at least when using the driver in irq mode. The same
size determined for the TX FIFO is also assumed for the RX FIFO. When a
SPI transaction wants to write the amount of the FIFO size or more
bytes, the following happens, for example with 16 bytes FIFO size:
The driver stops the SPI hardware and writes 17 bytes to the TX FIFO and
starts the SPI hardware and goes sleep.
The hardware then shifts out 17 bytes (FIFO + shift register) and
simultaneously reads bytes into the RX FIFO, but it only has 16 places,
so it looses one byte. Then TX FIFO empty asserts, wakes the driver
again, which has a fast path and reads 16 bytes from the RX FIFO, but
before reading the last 17th byte (which is lost) it does this:
sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
if (!(sr & XSPI_SR_RX_EMPTY_MASK)) {
xilinx_spi_rx(xspi);
rx_words--;
}
It reads the status register and checks if the RX FIFO is not empty.
But it is empty in our case. So this check spins in a while loop
forever locking the driver.
This patch fixes the logic to determine the FIFO size.
A flaw was found in the Linux kernel's spi: xilinx driver. The driver incorrectly determines the size of its internal buffer, a First-In, First-Out (FIFO) queue. This miscalculation can lead to an overflow when the driver attempts to write more data than the FIFO can hold during a Serial Peripheral Interface (SPI) transaction. This causes the driver to lose data and enter an infinite loop, resulting in a denial of service (DoS) for the system.
Затронутые пакеты
| Платформа | Пакет | Состояние | Рекомендация | Релиз |
|---|---|---|---|---|
| Red Hat Enterprise Linux 10 | kernel | Not affected | ||
| Red Hat Enterprise Linux 6 | kernel | Not affected | ||
| Red Hat Enterprise Linux 7 | kernel | Not affected | ||
| Red Hat Enterprise Linux 7 | kernel-rt | Not affected | ||
| Red Hat Enterprise Linux 8 | kernel | Not affected | ||
| Red Hat Enterprise Linux 8 | kernel-rt | Not affected | ||
| Red Hat Enterprise Linux 9 | kernel | Not affected | ||
| Red Hat Enterprise Linux 9 | kernel-rt | Not affected |
Показывать по
Дополнительная информация
Статус:
EPSS
5.5 Medium
CVSS3
Связанные уязвимости
In the Linux kernel, the following vulnerability has been resolved: spi: xilinx: use FIFO occupancy register to determine buffer size The method the driver uses to determine the size of the FIFO has a problem. What it currently does is this: It stops the SPI hardware and writes to the TX FIFO register until TX FIFO FULL asserts in the status register. But the hardware does not only have the FIFO, it also has a shift register which can hold a byte. This can be seen, when writing a byte to the FIFO (while the SPI hardware is stopped,) the TX FIFO EMPTY is still empty. So, if we have a FIFO size of 16 for example, the current method returns a 17. This is a problem, at least when using the driver in irq mode. The same size determined for the TX FIFO is also assumed for the RX FIFO. When a SPI transaction wants to write the amount of the FIFO size or more bytes, the following happens, for example with 16 bytes FIFO size: The driver stops the SPI hardware and writes 17 bytes to the TX FIF...
In the Linux kernel, the following vulnerability has been resolved: spi: xilinx: use FIFO occupancy register to determine buffer size The method the driver uses to determine the size of the FIFO has a problem. What it currently does is this: It stops the SPI hardware and writes to the TX FIFO register until TX FIFO FULL asserts in the status register. But the hardware does not only have the FIFO, it also has a shift register which can hold a byte. This can be seen, when writing a byte to the FIFO (while the SPI hardware is stopped,) the TX FIFO EMPTY is still empty. So, if we have a FIFO size of 16 for example, the current method returns a 17. This is a problem, at least when using the driver in irq mode. The same size determined for the TX FIFO is also assumed for the RX FIFO. When a SPI transaction wants to write the amount of the FIFO size or more bytes, the following happens, for example with 16 bytes FIFO size: The driver stops the SPI hardware and writes 17 bytes to the TX FIFO
In the Linux kernel, the following vulnerability has been resolved: s ...
In the Linux kernel, the following vulnerability has been resolved: spi: xilinx: use FIFO occupancy register to determine buffer size The method the driver uses to determine the size of the FIFO has a problem. What it currently does is this: It stops the SPI hardware and writes to the TX FIFO register until TX FIFO FULL asserts in the status register. But the hardware does not only have the FIFO, it also has a shift register which can hold a byte. This can be seen, when writing a byte to the FIFO (while the SPI hardware is stopped,) the TX FIFO EMPTY is still empty. So, if we have a FIFO size of 16 for example, the current method returns a 17. This is a problem, at least when using the driver in irq mode. The same size determined for the TX FIFO is also assumed for the RX FIFO. When a SPI transaction wants to write the amount of the FIFO size or more bytes, the following happens, for example with 16 bytes FIFO size: The driver stops the SPI hardware and writes 17 bytes to the TX F...
EPSS
5.5 Medium
CVSS3