Описание
In the Linux kernel, the following vulnerability has been resolved:
tty: serial: max3100: shut down timer before freeing port
max3100_shutdown() stops the polling timer but returns early during
system suspend. If the SPI device is unbound before resume, the serial
core does not call max3100_shutdown() again, so max3100_remove() frees
the port while the timer remains armed. max3100_timeout() may then
access the freed port and re-arm the timer.
Add final timer teardown to max3100_remove() and use
timer_shutdown_sync() to prevent a racing callback from re-arming it.
Also free the IRQ and destroy the workqueue there before freeing the
port. Keep timer_delete_sync() in max3100_shutdown() so that a
subsequent open() can re-arm the timer.
The workqueue is created before request_irq() and destroyed on both
request_irq() failure and normal shutdown. Its presence at remove thus
identifies the IRQ left registered when suspend bypasses shutdown.
Free the IRQ before destroying the workqueue, in both
max3100_shutdown() and max3100_remove(), and cancel the pending work
in between. free_irq() waits for a running interrupt handler to
finish and no new handler can start afterwards, so a racing handler
cannot queue work on a workqueue that is being destroyed; the
force_end_work check in max3100_dowork() only narrows that window, as
a handler delayed between the check and queue_work() could still run
after the teardown has cleared the workqueue pointer. Cancelling the
work also keeps destroy_workqueue() from waiting on a queued work item
in case remove() ever runs while the freezable workqueue is still
frozen, e.g. device removal during the resume window, before
workqueues are thawed.
This issue was found by an in-house static analysis tool.
A flaw was found in the MAX3100 serial driver in the Linux kernel. This flaw allows a local privileged user to cause a Denial of Service (DoS) or memory corruption by unbinding the device during a system suspend cycle. In this scenario, the driver releases the device port memory while an active polling timer is still running. When the timer callback executes, it accesses the already-freed memory, triggering a use-after-free condition that can crash the system.
Отчет
A race in the MAX3100 serial driver can leave the polling timer armed when the SPI device is removed during the suspend window. max3100_remove can then free the port while max3100_timeout still holds a reference to it, allowing the callback to access freed memory and rearm the timer. The IRQ and workqueue teardown order also permits a racing interrupt handler to interact with workqueue state during removal. For the CVSS the PR:L value in the paranoid score represents environments where device teardown is delegated to a reduced capability root, container manager, or service account. A standard system normally requires administrative privileges and is better represented by PR:H. The issue is local and is not network reachable. Impact is at least denial of service through a kernel crash.
Меры по смягчению последствий
Mitigation for this issue is either not available or the currently available options don't meet the Red Hat Product Security criteria comprising ease of use and deployment, applicability to widespread installation base or stability.
Затронутые пакеты
| Платформа | Пакет | Состояние | Рекомендация | Релиз |
|---|---|---|---|---|
| Red Hat Enterprise Linux 10 | kernel | Fix deferred |
Показывать по
Ссылки на источники
Дополнительная информация
Статус:
EPSS
4.7 Medium
CVSS3
Связанные уязвимости
In the Linux kernel, the following vulnerability has been resolved: tty: serial: max3100: shut down timer before freeing port max3100_shutdown() stops the polling timer but returns early during system suspend. If the SPI device is unbound before resume, the serial core does not call max3100_shutdown() again, so max3100_remove() frees the port while the timer remains armed. max3100_timeout() may then access the freed port and re-arm the timer. Add final timer teardown to max3100_remove() and use timer_shutdown_sync() to prevent a racing callback from re-arming it. Also free the IRQ and destroy the workqueue there before freeing the port. Keep timer_delete_sync() in max3100_shutdown() so that a subsequent open() can re-arm the timer. The workqueue is created before request_irq() and destroyed on both request_irq() failure and normal shutdown. Its presence at remove thus identifies the IRQ left registered when suspend bypasses shutdown. Free the IRQ before destroying the workqueue, in ...
In the Linux kernel, the following vulnerability has been resolved: tty: serial: max3100: shut down timer before freeing port max3100_shutdown() stops the polling timer but returns early during system suspend. If the SPI device is unbound before resume, the serial core does not call max3100_shutdown() again, so max3100_remove() frees the port while the timer remains armed. max3100_timeout() may then access the freed port and re-arm the timer. Add final timer teardown to max3100_remove() and use timer_shutdown_sync() to prevent a racing callback from re-arming it. Also free the IRQ and destroy the workqueue there before freeing the port. Keep timer_delete_sync() in max3100_shutdown() so that a subsequent open() can re-arm the timer. The workqueue is created before request_irq() and destroyed on both request_irq() failure and normal shutdown. Its presence at remove thus identifies the IRQ left registered when suspend bypasses shutdown. Free the IRQ before destroying the workqueue, i
In the Linux kernel, the following vulnerability has been resolved: t ...
In the Linux kernel, the following vulnerability has been resolved: tty: serial: max3100: shut down timer before freeing port max3100_shutdown() stops the polling timer but returns early during system suspend. If the SPI device is unbound before resume, the serial core does not call max3100_shutdown() again, so max3100_remove() frees the port while the timer remains armed. max3100_timeout() may then access the freed port and re-arm the timer. Add final timer teardown to max3100_remove() and use timer_shutdown_sync() to prevent a racing callback from re-arming it. Also free the IRQ and destroy the workqueue there before freeing the port. Keep timer_delete_sync() in max3100_shutdown() so that a subsequent open() can re-arm the timer. The workqueue is created before request_irq() and destroyed on both request_irq() failure and normal shutdown. Its presence at remove thus identifies the IRQ left registered when suspend bypasses shutdown. Free the IRQ before destroying the workqueue...
EPSS
4.7 Medium
CVSS3