Описание
In the Linux kernel, the following vulnerability has been resolved:
HID: multitouch: stop the release timer from being rearmed on remove
mt_remove() quiesces the sticky-finger timer before stopping the
hardware:
timer_delete_sync(&td->release_timer);
sysfs_remove_group(&hdev->dev.kobj, &mt_attribute_group);
hid_hw_stop(hdev);
timer_delete_sync() waits for a running callback and dequeues the timer,
but it does not stop the timer from being armed again. The transport is
still delivering reports at that point, and the report path rearms it:
if (app->quirks & MT_QUIRK_STICKY_FINGERS) {
if (td->mt_io_flags & MT_IO_SLOTS_MASK)
mod_timer(&td->release_timer,
jiffies + msecs_to_jiffies(100));
A report that arrives after timer_delete_sync() has returned therefore
leaves the timer queued. td is allocated with devm_kzalloc() against
hdev->dev, so it is freed when the driver is unbound, after mt_remove()
returns. When the timer fires afterwards, mt_expired_timeout()
dereferences the freed td:
struct mt_device *td = timer_container_of(td, t, release_timer);
struct hid_device *hdev = td->hdev;
if (test_and_set_bit_lock(MT_IO_FLAGS_RUNNING, &td->mt_io_flags))
Simply moving the teardown after hid_hw_stop() does not fix this on its
own, because mt_expired_timeout() calls mt_release_contacts(), which
walks hdev->inputs; the timer still has to be quiesced before
hid_hw_stop() tears the input devices down.
Use timer_shutdown_sync() instead, which additionally makes any later
mod_timer() a no-op, so neither ordering constraint has to be traded off
against the other. This is the final-teardown pattern the function was
introduced for, and hid-wiimote already uses it for the same reason.
A flaw was found in the Linux kernel's Human Interface Device (HID) multitouch driver. When a multitouch device is disconnected or removed, the driver fails to prevent the release timer from being rescheduled by incoming input reports. Once the driver deallocates the device data, the timer callback executes and attempts to access the freed memory, resulting in a use-after-free condition. A local attacker could exploit this flaw to cause a Denial of Service (DoS) by crashing the system.
Отчет
A race in the HID multitouch removal path can rearm release_timer after timer_delete_sync has already returned. The mt_device object is freed after mt_remove completes, but the queued timer can later execute mt_expired_timeout and dereference the released td object. The callback reads td hdev and performs a bit operation on td mt_io_flags, so the issue includes access to and modification of freed memory rather than only a harmless stale timer warning. For the CVSS the PR:N value reflects a malicious attached HID device that can deliver reports and disconnect without holding an account or privilege on the target. The paranoid AV:A interpretation is applicable only where an affected HID transport can be reached over an adjacent connection such as Bluetooth. Typical USB exploitation instead requires physical device access and the race has AC:H because a report must arrive during the narrow teardown window. The issue is not directly reachable over ordinary IP networks or the public Internet.
Меры по смягчению последствий
Mitigation for this issue is either not available or the currently available options don't meet the Red Hat Product Security criteria comprising ease of use and deployment, applicability to widespread installation base or stability.
Затронутые пакеты
| Платформа | Пакет | Состояние | Рекомендация | Релиз |
|---|---|---|---|---|
| Red Hat Enterprise Linux 10 | kernel | Fix deferred |
Показывать по
Ссылки на источники
Дополнительная информация
Статус:
EPSS
5.3 Medium
CVSS3
Связанные уязвимости
In the Linux kernel, the following vulnerability has been resolved: HID: multitouch: stop the release timer from being rearmed on remove mt_remove() quiesces the sticky-finger timer before stopping the hardware: timer_delete_sync(&td->release_timer); sysfs_remove_group(&hdev->dev.kobj, &mt_attribute_group); hid_hw_stop(hdev); timer_delete_sync() waits for a running callback and dequeues the timer, but it does not stop the timer from being armed again. The transport is still delivering reports at that point, and the report path rearms it: if (app->quirks & MT_QUIRK_STICKY_FINGERS) { if (td->mt_io_flags & MT_IO_SLOTS_MASK) mod_timer(&td->release_timer, jiffies + msecs_to_jiffies(100)); A report that arrives after timer_delete_sync() has returned therefore leaves the timer queued. td is allocated with devm_kzalloc() against hdev->dev, so it is freed when the driver is unbound, after mt_remove() returns. When the timer fires afterwards, mt_expired_timeout() dereferences the freed td: st...
In the Linux kernel, the following vulnerability has been resolved: HID: multitouch: stop the release timer from being rearmed on remove mt_remove() quiesces the sticky-finger timer before stopping the hardware: timer_delete_sync(&td->release_timer); sysfs_remove_group(&hdev->dev.kobj, &mt_attribute_group); hid_hw_stop(hdev); timer_delete_sync() waits for a running callback and dequeues the timer, but it does not stop the timer from being armed again. The transport is still delivering reports at that point, and the report path rearms it: if (app->quirks & MT_QUIRK_STICKY_FINGERS) { if (td->mt_io_flags & MT_IO_SLOTS_MASK) mod_timer(&td->release_timer, jiffies + msecs_to_jiffies(100)); A report that arrives after timer_delete_sync() has returned therefore leaves the timer queued. td is allocated with devm_kzalloc() against hdev->dev, so it is freed when the driver is unbound, after mt_remove() returns. When the timer fires
HID: multitouch: stop the release timer from being rearmed on remove
In the Linux kernel, the following vulnerability has been resolved: H ...
In the Linux kernel, the following vulnerability has been resolved: HID: multitouch: stop the release timer from being rearmed on remove mt_remove() quiesces the sticky-finger timer before stopping the hardware: timer_delete_sync(&td->release_timer); sysfs_remove_group(&hdev->dev.kobj, &mt_attribute_group); hid_hw_stop(hdev); timer_delete_sync() waits for a running callback and dequeues the timer, but it does not stop the timer from being armed again. The transport is still delivering reports at that point, and the report path rearms it: if (app->quirks & MT_QUIRK_STICKY_FINGERS) { if (td->mt_io_flags & MT_IO_SLOTS_MASK) mod_timer(&td->release_timer, jiffies + msecs_to_jiffies(100)); A report that arrives after timer_delete_sync() has returned therefore leaves the timer queued. td is allocated with devm_kzalloc() against hdev->dev, so it is freed when the driver is unbound, after mt_remove() returns. When the timer fir...
EPSS
5.3 Medium
CVSS3