In the Linux kernel, the following vulnerability has been resolved: media: b2c2: Fix use-after-free causing by irq_check_work in flexcop_pci_remove The original code uses cancel_delayed_work() in flexcop_pci_remove(), which does not guarantee that the delayed work item irq_check_work has fully completed if it was already running. This leads to use-after-free scenarios where flexcop_pci_remove() may free the flexcop_device while irq_check_work is still active and attempts to dereference the device. A typical race condition is illustrated below: CPU 0 (remove) | CPU 1 (delayed work callback) flexcop_pci_remove() | flexcop_pci_irq_check_work() cancel_delayed_work() | flexcop_device_kfree(fc_pci->fc_dev) | | fc = fc_pci->fc_dev; // UAF This is confirmed by a KASAN report: ================================================================== BUG: KASAN: slab-use-after-free in __run_timer_base.part.0+0x7d7/0x8c0 Write of size 8 at ad...

In the Linux kernel, the following vulnerability has been resolved: media: i2c: tc358743: Fix use-after-free bugs caused by orphan timer in probe The state->timer is a cyclic timer that schedules work_i2c_poll and delayed_work_enable_hotplug, while rearming itself. Using timer_delete() fails to guarantee the timer isn't still running when destroyed, similarly cancel_delayed_work() cannot ensure delayed_work_enable_hotplug has terminated if already executing. During probe failure after timer initialization, these may continue running as orphans and reference the already-freed tc358743_state object through tc358743_irq_poll_timer. The following is the trace captured by KASAN. BUG: KASAN: slab-use-after-free in __run_timer_base.part.0+0x7d7/0x8c0 Write of size 8 at addr ffff88800ded83c8 by task swapper/1/0 ... Call Trace: <IRQ> dump_stack_lvl+0x55/0x70 print_report+0xcf/0x610 ? __pfx_sched_balance_find_src_group+0x10/0x10 ? __run_timer_base.part.0+0x7d7/0x8c0 kasan_report+0xb8/0xf0 ? _...

In the Linux kernel, the following vulnerability has been resolved: media: tuner: xc5000: Fix use-after-free in xc5000_release The original code uses cancel_delayed_work() in xc5000_release(), which does not guarantee that the delayed work item timer_sleep has fully completed if it was already running. This leads to use-after-free scenarios where xc5000_release() may free the xc5000_priv while timer_sleep is still active and attempts to dereference the xc5000_priv. A typical race condition is illustrated below: CPU 0 (release thread) | CPU 1 (delayed work callback) xc5000_release() | xc5000_do_timer_sleep() cancel_delayed_work() | hybrid_tuner_release_state(priv) | kfree(priv) | | priv = container_of() // UAF Replace cancel_delayed_work() with cancel_delayed_work_sync() to ensure that the timer_sleep is properly canceled before the xc5000_priv memory is deallocated. A deadlock concern was considered: x...

In the Linux kernel, the following vulnerability has been resolved: media: rc: fix races with imon_disconnect() Syzbot reports a KASAN issue as below: BUG: KASAN: use-after-free in __create_pipe include/linux/usb.h:1945 [inline] BUG: KASAN: use-after-free in send_packet+0xa2d/0xbc0 drivers/media/rc/imon.c:627 Read of size 4 at addr ffff8880256fb000 by task syz-executor314/4465 CPU: 2 PID: 4465 Comm: syz-executor314 Not tainted 6.0.0-rc1-syzkaller #0 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-2 04/01/2014 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106 print_address_description mm/kasan/report.c:317 [inline] print_report.cold+0x2ba/0x6e9 mm/kasan/report.c:433 kasan_report+0xb1/0x1e0 mm/kasan/report.c:495 __create_pipe include/linux/usb.h:1945 [inline] send_packet+0xa2d/0xbc0 drivers/media/rc/imon.c:627 vfd_write+0x2d9/0x550 drivers/media/rc/imon.c:991 vfs_write+0x2d7/0xdd0 fs/read_write.c:576 ksys_write+...

In the Linux kernel, the following vulnerability has been resolved: mm: swap: check for stable address space before operating on the VMA It is possible to hit a zero entry while traversing the vmas in unuse_mm() called from swapoff path and accessing it causes the OOPS: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000446--> Loading the memory from offset 0x40 on the XA_ZERO_ENTRY as address. Mem abort info: ESR = 0x0000000096000005 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x05: level 1 translation fault The issue is manifested from the below race between the fork() on a process and swapoff: fork(dup_mmap())swapoff(unuse_mm) --------------- ----------------- 1) Identical mtree is built using __mt_dup(). 2) copy_pte_range()--> copy_nonpresent_pte(): The dst mm is added into the mmlist to be visible to the swapoff operation. 3) Fatal signal is sent to the parent process(which is the curr...

In the Linux kernel, the following vulnerability has been resolved: wifi: ath11k: fix NULL dereference in ath11k_qmi_m3_load() If ab->fw.m3_data points to data, then fw pointer remains null. Further, if m3_mem is not allocated, then fw is dereferenced to be passed to ath11k_err function. Replace fw->size by m3_len. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: bpf: Check the helper function is valid in get_helper_proto kernel test robot reported verifier bug [1] where the helper func pointer could be NULL due to disabled config option. As Alexei suggested we could check on that in get_helper_proto directly. Marking tail_call helper func with BPF_PTR_POISON, because it is unused by design. [1] https://lore.kernel.org/oe-lkp/202507160818.68358831-lkp@intel.com

In the Linux kernel, the following vulnerability has been resolved: x86/mce: use is_copy_from_user() to determine copy-from-user context Patch series "mm/hwpoison: Fix regressions in memory failure handling", v4. ## 1. What am I trying to do: This patchset resolves two critical regressions related to memory failure handling that have appeared in the upstream kernel since version 5.17, as compared to 5.10 LTS. - copyin case: poison found in user page while kernel copying from user space - instr case: poison found while instruction fetching in user space ## 2. What is the expected outcome and why - For copyin case: Kernel can recover from poison found where kernel is doing get_user() or copy_from_user() if those places get an error return and the kernel return -EFAULT to the process instead of crashing. More specifily, MCE handler checks the fixup handler type to decide whether an in kernel #MC can be recovered. When EX_TYPE_UACCESS is found, the PC jumps to recovery code specified ...

In the Linux kernel, the following vulnerability has been resolved: can: etas_es58x: populate ndo_change_mtu() to prevent buffer overflow Sending an PF_PACKET allows to bypass the CAN framework logic and to directly reach the xmit() function of a CAN driver. The only check which is performed by the PF_PACKET framework is to make sure that skb->len fits the interface's MTU. Unfortunately, because the etas_es58x driver does not populate its net_device_ops->ndo_change_mtu(), it is possible for an attacker to configure an invalid MTU by doing, for example: $ ip link set can0 mtu 9999 After doing so, the attacker could open a PF_PACKET socket using the ETH_P_CANXL protocol: socket(PF_PACKET, SOCK_RAW, htons(ETH_P_CANXL)); to inject a malicious CAN XL frames. For example: struct canxl_frame frame = { .flags = 0xff, .len = 2048, }; The CAN drivers' xmit() function are calling can_dev_dropped_skb() to check that the skb is valid, unfortunately under above conditions, the malicious packet is...

In the Linux kernel, the following vulnerability has been resolved: can: hi311x: populate ndo_change_mtu() to prevent buffer overflow Sending an PF_PACKET allows to bypass the CAN framework logic and to directly reach the xmit() function of a CAN driver. The only check which is performed by the PF_PACKET framework is to make sure that skb->len fits the interface's MTU. Unfortunately, because the sun4i_can driver does not populate its net_device_ops->ndo_change_mtu(), it is possible for an attacker to configure an invalid MTU by doing, for example: $ ip link set can0 mtu 9999 After doing so, the attacker could open a PF_PACKET socket using the ETH_P_CANXL protocol: socket(PF_PACKET, SOCK_RAW, htons(ETH_P_CANXL)) to inject a malicious CAN XL frames. For example: struct canxl_frame frame = { .flags = 0xff, .len = 2048, }; The CAN drivers' xmit() function are calling can_dev_dropped_skb() to check that the skb is valid, unfortunately under above conditions, the malicious packet is able ...

In the Linux kernel, the following vulnerability has been resolved: can: sun4i_can: populate ndo_change_mtu() to prevent buffer overflow Sending an PF_PACKET allows to bypass the CAN framework logic and to directly reach the xmit() function of a CAN driver. The only check which is performed by the PF_PACKET framework is to make sure that skb->len fits the interface's MTU. Unfortunately, because the sun4i_can driver does not populate its net_device_ops->ndo_change_mtu(), it is possible for an attacker to configure an invalid MTU by doing, for example: $ ip link set can0 mtu 9999 After doing so, the attacker could open a PF_PACKET socket using the ETH_P_CANXL protocol: socket(PF_PACKET, SOCK_RAW, htons(ETH_P_CANXL)) to inject a malicious CAN XL frames. For example: struct canxl_frame frame = { .flags = 0xff, .len = 2048, }; The CAN drivers' xmit() function are calling can_dev_dropped_skb() to check that the skb is valid, unfortunately under above conditions, the malicious packet is ab...

In the Linux kernel, the following vulnerability has been resolved: can: mcba_usb: populate ndo_change_mtu() to prevent buffer overflow Sending an PF_PACKET allows to bypass the CAN framework logic and to directly reach the xmit() function of a CAN driver. The only check which is performed by the PF_PACKET framework is to make sure that skb->len fits the interface's MTU. Unfortunately, because the mcba_usb driver does not populate its net_device_ops->ndo_change_mtu(), it is possible for an attacker to configure an invalid MTU by doing, for example: $ ip link set can0 mtu 9999 After doing so, the attacker could open a PF_PACKET socket using the ETH_P_CANXL protocol: socket(PF_PACKET, SOCK_RAW, htons(ETH_P_CANXL)) to inject a malicious CAN XL frames. For example: struct canxl_frame frame = { .flags = 0xff, .len = 2048, }; The CAN drivers' xmit() function are calling can_dev_dropped_skb() to check that the skb is valid, unfortunately under above conditions, the malicious packet is able...

In the Linux kernel, the following vulnerability has been resolved: net: tun: Update napi->skb after XDP process The syzbot report a UAF issue: BUG: KASAN: slab-use-after-free in skb_reset_mac_header include/linux/skbuff.h:3150 [inline] BUG: KASAN: slab-use-after-free in napi_frags_skb net/core/gro.c:723 [inline] BUG: KASAN: slab-use-after-free in napi_gro_frags+0x6e/0x1030 net/core/gro.c:758 Read of size 8 at addr ffff88802ef22c18 by task syz.0.17/6079 CPU: 0 UID: 0 PID: 6079 Comm: syz.0.17 Not tainted syzkaller #0 PREEMPT(full) Call Trace: <TASK> dump_stack_lvl+0x189/0x250 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:378 [inline] print_report+0xca/0x240 mm/kasan/report.c:482 kasan_report+0x118/0x150 mm/kasan/report.c:595 skb_reset_mac_header include/linux/skbuff.h:3150 [inline] napi_frags_skb net/core/gro.c:723 [inline] napi_gro_frags+0x6e/0x1030 net/core/gro.c:758 tun_get_user+0x28cb/0x3e20 drivers/net/tun.c:1920 tun_chr_write_iter+0x113/0x200 drivers/net/tun....

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_event: Fix UAF in hci_conn_tx_dequeue This fixes the following UAF caused by not properly locking hdev when processing HCI_EV_NUM_COMP_PKTS: BUG: KASAN: slab-use-after-free in hci_conn_tx_dequeue+0x1be/0x220 net/bluetooth/hci_conn.c:3036 Read of size 4 at addr ffff8880740f0940 by task kworker/u11:0/54 CPU: 1 UID: 0 PID: 54 Comm: kworker/u11:0 Not tainted 6.16.0-rc7 #3 PREEMPT(full) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014 Workqueue: hci1 hci_rx_work Call Trace: <TASK> dump_stack_lvl+0x189/0x250 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:378 [inline] print_report+0xca/0x230 mm/kasan/report.c:480 kasan_report+0x118/0x150 mm/kasan/report.c:593 hci_conn_tx_dequeue+0x1be/0x220 net/bluetooth/hci_conn.c:3036 hci_num_comp_pkts_evt+0x1c8/0xa50 net/bluetooth/hci_event.c:4404 hci_event_func net/bluetooth/hci_event.c:7477 [inline] hci_event_packe...

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_event: Fix UAF in hci_acl_create_conn_sync This fixes the following UFA in hci_acl_create_conn_sync where a connection still pending is command submission (conn->state == BT_OPEN) maybe freed, also since this also can happen with the likes of hci_le_create_conn_sync fix it as well: BUG: KASAN: slab-use-after-free in hci_acl_create_conn_sync+0x5ef/0x790 net/bluetooth/hci_sync.c:6861 Write of size 2 at addr ffff88805ffcc038 by task kworker/u11:2/9541 CPU: 1 UID: 0 PID: 9541 Comm: kworker/u11:2 Not tainted 6.16.0-rc7 #3 PREEMPT(full) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014 Workqueue: hci3 hci_cmd_sync_work Call Trace: <TASK> dump_stack_lvl+0x189/0x250 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:378 [inline] print_report+0xca/0x230 mm/kasan/report.c:480 kasan_report+0x118/0x150 mm/kasan/report.c:593 hci_acl_create_conn_sync+0x5ef/0x790 ne...

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: MGMT: Fix possible UAFs This attemps to fix possible UAFs caused by struct mgmt_pending being freed while still being processed like in the following trace, in order to fix mgmt_pending_valid is introduce and use to check if the mgmt_pending hasn't been removed from the pending list, on the complete callbacks it is used to check and in addtion remove the cmd from the list while holding mgmt_pending_lock to avoid TOCTOU problems since if the cmd is left on the list it can still be accessed and freed. BUG: KASAN: slab-use-after-free in mgmt_add_adv_patterns_monitor_sync+0x35/0x50 net/bluetooth/mgmt.c:5223 Read of size 8 at addr ffff8880709d4dc0 by task kworker/u11:0/55 CPU: 0 UID: 0 PID: 55 Comm: kworker/u11:0 Not tainted 6.16.4 #2 PREEMPT(full) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014 Workqueue: hci0 hci_cmd_sync_work Call Trace: <TASK> dump_stack_lvl+0x189/0x2...

In the Linux kernel, the following vulnerability has been resolved: nexthop: Forbid FDB status change while nexthop is in a group The kernel forbids the creation of non-FDB nexthop groups with FDB nexthops: # ip nexthop add id 1 via 192.0.2.1 fdb # ip nexthop add id 2 group 1 Error: Non FDB nexthop group cannot have fdb nexthops. And vice versa: # ip nexthop add id 3 via 192.0.2.2 dev dummy1 # ip nexthop add id 4 group 3 fdb Error: FDB nexthop group can only have fdb nexthops. However, as long as no routes are pointing to a non-FDB nexthop group, the kernel allows changing the type of a nexthop from FDB to non-FDB and vice versa: # ip nexthop add id 5 via 192.0.2.2 dev dummy1 # ip nexthop add id 6 group 5 # ip nexthop replace id 5 via 192.0.2.2 fdb # echo $? 0 This configuration is invalid and can result in a NPD [1] since FDB nexthops are not associated with a nexthop device: # ip route add 198.51.100.1/32 nhid 6 # ping 198.51.100.1 Fix by preventing nexthop FDB status change while...

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: fs, fix UAF in flow counter release Fix a kernel trace [1] caused by releasing an HWS action of a local flow counter in mlx5_cmd_hws_delete_fte(), where the HWS action refcount and mutex were not initialized and the counter struct could already be freed when deleting the rule. Fix it by adding the missing initializations and adding refcount for the local flow counter struct. [1] Kernel log: Call Trace: <TASK> dump_stack_lvl+0x34/0x48 mlx5_fs_put_hws_action.part.0.cold+0x21/0x94 [mlx5_core] mlx5_fc_put_hws_action+0x96/0xad [mlx5_core] mlx5_fs_destroy_fs_actions+0x8b/0x152 [mlx5_core] mlx5_cmd_hws_delete_fte+0x5a/0xa0 [mlx5_core] del_hw_fte+0x1ce/0x260 [mlx5_core] mlx5_del_flow_rules+0x12d/0x240 [mlx5_core] ? ttwu_queue_wakelist+0xf4/0x110 mlx5_ib_destroy_flow+0x103/0x1b0 [mlx5_ib] uverbs_free_flow+0x20/0x50 [ib_uverbs] destroy_hw_idr_uobject+0x1b/0x50 [ib_uverbs] uverbs_destroy_uobject+0x34/0x1a0 [ib_uverbs...

In the Linux kernel, the following vulnerability has been resolved: octeontx2-pf: Fix potential use after free in otx2_tc_add_flow() This code calls kfree_rcu(new_node, rcu) and then dereferences "new_node" and then dereferences it on the next line. Two lines later, we take a mutex so I don't think this is an RCU safe region. Re-order it to do the dereferences before queuing up the free.

In the Linux kernel, the following vulnerability has been resolved: futex: Prevent use-after-free during requeue-PI syzbot managed to trigger the following race: T1 T2 futex_wait_requeue_pi() futex_do_wait() schedule() futex_requeue() futex_proxy_trylock_atomic() futex_requeue_pi_prepare() requeue_pi_wake_futex() futex_requeue_pi_complete() /* preempt */ * timeout/ signal wakes T1 * futex_requeue_pi_wakeup_sync() // Q_REQUEUE_PI_LOCKED futex_hash_put() // back to userland, on stack futex_q is garbage /* back */ wake_up_state(q->task, TASK_NORMAL); In this scenario futex_wait_requeue_pi() is able to leave without using futex_q::lock_ptr for synchronization. This can be prevented by reading futex_q::task before updating the futex_q::requeue_state. A reference on the task_struct is not needed because requeue_pi_wake_futex() is invoked with a spinlock_t held which implies a RCU read section. Even if T1 terminates immediately after, the task_struct will rema...