In the Linux kernel, the following vulnerability has been resolved: power: supply: bq25890: Fix power_supply reference leak bq25890_fw_probe() acquires a reference to a secondary charger using power_supply_get_by_name(), but the reference is not released on later probe failures or on driver detach. In particular, failures after bq25890_fw_probe() returns successfully, such as a failure in bq25890_hw_init(), also leak the reference. Register a device-managed cleanup action immediately after acquiring the secondary charger. This releases the reference on all subsequent probe failures and on driver detach. Found by code review.

In the Linux kernel, the following vulnerability has been resolved: power: supply: charger-manager: register regulators before exposing sysfs charger_manager_remove() and the err_reg_extcon probe error path free each charger regulator with regulator_put() before tearing down the power_supply sysfs entries (power_supply_unregister()). charger_manager_remove() also calls try_charger_enable(cm, false) after the regulator_put() loop. A concurrent write to a charger's externally_control sysfs attribute that lands between regulator_put() and power_supply_unregister() can run charger_externally_control_store() and call try_charger_enable(), which, when charging is enabled, dereferences the already-freed consumer handle. When charging is enabled, try_charger_enable(cm, false) in .remove() also dereferences the freed handles directly. Both leave use-after-free windows. Symmetrically, probe registers the sysfs entries (power_supply_register) before acquiring the regulators (regulator_get, insi

In the Linux kernel, the following vulnerability has been resolved: power: supply: cros_usbpd-charger: bound the EC-reported port count cros_usbpd_charger_probe() reads two port counts from the EC and uses one of them, num_charger_ports, as the loop bound when populating a fixed-size array: struct port_data *ports[EC_USB_PD_MAX_PORTS]; /* 8 entries */ ... for (i = 0; i < charger->num_charger_ports; i++) charger->ports[charger->num_registered_psy++] = port; Both num_usbpd_ports (from EC_CMD_USB_PD_PORTS) and num_charger_ports (from EC_CMD_CHARGE_PORT_COUNT) are u8 values reported by the EC. The only validation is a sanity check that compares the two EC-reported values against each other: if (num_charger_ports < num_usbpd_ports || num_charger_ports > num_usbpd_ports + 1) return -EPROTO; It never checks either count against EC_USB_PD_MAX_PORTS, the size of the ports[] array. A malfunctioning, malicious or compromised EC that reports num_usbpd_ports == num_charger_ports

In the Linux kernel, the following vulnerability has been resolved: power: supply: cros_usbpd: Limit port counts to EC_USB_PD_MAX_PORTS Currently the cros_usbpd-charger driver probe iterates based on raw charger port count returned by the embedded controller. The only check is against the number of USB PD ports which the embedded controller also defines. A malicious embedded controller could return an inaccurate port count (up to 255) resulting in an out of bounds write and subsequent memory corruption. Update helper functions in cros_usbpd-charger to limit port counts to EC_USB_PD_MAX_PORTS.

Incorrect boundary conditions in the Audio/Video: Web Codecs component. This vulnerability was fixed in Firefox 151, Firefox ESR 115.36, Firefox ESR 140.11, Thunderbird 151, and Thunderbird 140.11.

In the Linux kernel, the following vulnerability has been resolved: power: supply: lp8727: fix use-after-free in lp8727_release_irq() lp8727_isr_func(), the threaded IRQ handler, is the only caller that arms pchg->work via schedule_delayed_work(). lp8727_release_irq() currently cancels the work before freeing the IRQ, so an IRQ delivered in between can re-arm the work through the threaded handler. After .remove returns the devm layer frees pchg while lp8727_delayed_func() may still run and dereference it. Free the IRQ first so the threaded handler is quiesced and can no longer queue work, then cancel the delayed work to drain the final generation. This issue was found by an in-house static analysis tool.

In the Linux kernel, the following vulnerability has been resolved: power: supply: lp8788-charger: fix use-after-free on remove lp8788_charger_remove() flushes charger_work before unregistering the IRQs. An IRQ thread can queue charger_work after flush_work() has returned. The work can then run after devres frees pchg and dereference it in lp8788_charger_event(). Unregister the IRQs first. free_irq() waits for any running threaded handler, so no handler can queue more work afterwards. Then use cancel_work_sync() to cancel pending work or wait for running work to finish. This issue was found by an in-house static analysis tool.

In the Linux kernel, the following vulnerability has been resolved: power: supply: qcom_battmgr: fix use-after-free qcom_battmgr_pdr_notify() queues enable_work when the PMIC GLINK service comes up, and the worker recovers battmgr through container_of() to issue firmware requests. The PMIC GLINK client stays on the client list until its devres release action runs, so a PDR notification can keep queueing the work, and a pending or running worker can access battmgr after devres frees it. Make enable_work device-managed with devm_work_autocancel(), registered before the PMIC GLINK client is allocated. The devres cleanup then releases the client first, so no further notification can queue the work, and cancels the work before battmgr is freed. This issue was found by an in-house static analysis tool.

In the Linux kernel, the following vulnerability has been resolved: power: supply: qcom_battmgr: terminate the strings from firmware The qcom_battmgr_sc8280xp_strcpy() takes a Pascal-style string when the firmware sends one. Otherwise it copies all BATTMGR_STRING_LEN bytes and leaves the destination without a terminator. Those destinations are model_number, serial_number and oem_info, each BATTMGR_STRING_LEN and declared next to each other. They go out to user space as val->strval, which power_supply_format_property() prints with "%s", so a firmware string that fills the whole field makes that read run into the following members. Use strscpy() so the copy always terminates, the way the SM8350 path already does for the same field.

In the Linux kernel, the following vulnerability has been resolved: power: supply: rt9455: quiesce delayed work before teardown The threaded IRQ handler can queue pwr_rdy_work, max_charging_time_work and batt_presence_work. pwr_rdy_work and batt_presence_work can also queue max_charging_time_work, while batt_presence_work can requeue itself. rt9455_remove() cancels max_charging_time_work before batt_presence_work. The latter can therefore queue max_charging_time_work after it has already been cancelled: rt9455_remove() workqueue cancel pwr_rdy_work cancel max_charging_time_work batt_presence_work queues max_charging_time_work cancel batt_presence_work return devres frees rt9455_info max_charging_time_work dereferences rt9455_info The IRQ also remains registered until devres cleanup and

In the Linux kernel, the following vulnerability has been resolved: power: supply: twl4030_charger: cancel workers via devm bci is devm-allocated. Two workers (bci->work and bci->current_worker) dereference it. twl4030_bci_remove() disables charging and masks interrupts. It cancels neither worker. A worker pending at remove() can run after devm frees bci. The USB transceiver comes from devm_usb_get_phy_by_node(). devm unregisters its notifier only after remove() returns. A cancel_work_sync() in remove() can then race a notifier reschedule. devm_work_autocancel() and devm_delayed_work_autocancel() avoid that. They cancel the workers during devm release, before bci is freed. The current_worker is registered first, since devm will cancel in reverse order and bci->work can reschedule current_worker. [Move comment about order into the commit message]

In the Linux kernel, the following vulnerability has been resolved: power: supply: ucs1002: fix use-after-free on remove ucs1002 has no remove callback, so unbind runs entirely through devm. The alert IRQ handler queues the health_poll delayed work, and the work reschedules itself while the chip reports a bad-health condition. devm frees the alert IRQ, which only synchronizes the handler; it does not cancel the delayed work, which can then run after devm frees the driver data and dereference it. Register health_poll with devm_delayed_work_autocancel() before the alert IRQ is requested. devm then frees the IRQ before cancelling the work, so the handler can no longer queue it and the work is cancelled before the driver data is freed. This issue was found by an in-house static analysis tool.

In the Linux kernel, the following vulnerability has been resolved: power: supply: max17040: propagate register read errors max17040_get_vcell() and max17040_get_soc() ignore errors returned by regmap_read(). When an I2C transfer fails, the uninitialized register value is converted and reported to userspace as a valid voltage or state of charge. The polling worker can also replace the cached state of charge with the bogus value and emit a spurious change event. Propagate read errors through the power supply get_property callback and keep the last valid cached state of charge when polling fails.

In the Linux kernel, the following vulnerability has been resolved: power: supply: max17040: synchronize work cancellation on suspend max17040_work() requeues itself after every poll. cancel_delayed_work() only cancels a pending instance and does not wait for a callback that is already running. If system suspend races with the polling callback, the callback can continue accessing the fuel gauge and requeue itself after the suspend callback returns. Use cancel_delayed_work_sync() to ensure polling is quiesced before suspend completes.

In the Linux kernel, the following vulnerability has been resolved: s390/cpum_cf: Handle CPU hotplug via prepare/dead callbacks The command 'perf stat -e cycles -- <command>' crashes the kernel when CPUs are hotplug added during that run. Root cause is the allocation of struct cpu_cf_events at first event initialization. The allocation is dynamic and the first event that has task context creates such a structure for each online CPU. This is not sufficient. CPUs may be offline during event creation and can be set online during the perf run time. For example commands # echo 0 > /sys/devices/system/cpu/cpu1/online # perf stat -e cycles -i -- stress-ng -t10s --matrix X # sleep 1 # echo 1 > /sys/devices/system/cpu/cpu1/online create an event for CPUs 0,2-X. Since the events are created with task-context, the scheduler will eventually schedule the program on CPU1. This CPU has not created and initialized any per CPU event infrastructure as that CPU was not online at the time of the

Sandbox escape in Firefox and Firefox Focus for Android. This vulnerability was fixed in Firefox 151.

In the Linux kernel, the following vulnerability has been resolved: s390/percpu: Fix MVIY_PERCPU() with older binutils Commit a737737cdb9c ("s390/percpu: Infrastructure for more efficient this_cpu operations") introduced MVIY_PERCPU(), which stringifies arguments that are already C string literals. This generates an assembler macro invocation with whitespace-separated quoted arguments: GEN_MVIY "459712" "%r3" GNU as versions prior to binutils 2.39 drop the separating whitespace between quoted macro arguments during input scrubbing. They consequently parse the invocation as a single argument and emit repeated warnings: Warning: missing closing `"' The .ifc in GEN_MVIY never matches and GNU as exits successfully without emitting the mviy instruction. As a result, the interrupted per-CPU sequence is not marked in lowcore and the exception return path cannot repair the per-CPU address register after migration. All MVIY_PERCPU() callers pass C string literals. Use them directly a

In the Linux kernel, the following vulnerability has been resolved: s390/dasd: Do not complete a failed ESE read as successful dasd_int_handler() completes an NRF read of an unallocated ESE track by calling ese_read() and unconditionally marking the request DASD_CQR_SUCCESS. dasd_eckd_ese_read() can return an error before it has zeroed the destination buffer: a failed sense-data parse or a current track outside the requested range both return early, leaving the destination pages untouched. The request is still completed successfully, so the block layer is handed stale / uninitialized memory instead of zeros. Check the ese_read() return value and fail the request through the normal error path instead of forcing DASD_CQR_SUCCESS.

In the Linux kernel, the following vulnerability has been resolved: s390/dasd: Guard sysfs discipline callbacks against unallocated private data Several sysfs show/store handlers call a discipline callback that dereferences device->private, either directly or through the DASD_DEFINE_ATTR() macro. During dasd_generic_set_online() the discipline is assigned before check_device() allocates device->private, so an unprivileged read of one of these world-readable attributes in that window dereferences a NULL pointer and panics. Guard the dereference inside each callback that actually touches device->private.

In the Linux kernel, the following vulnerability has been resolved: s390/dasd: Propagate partial completion length across ERP recovery dasd_default_erp_postaction() copies the timing and device state from the finished ERP request back to the original request but drops proc_bytes. A request that was partially completed, an ESE read of a not-yet-allocated track returns fewer bytes than requested, and then recovered through the ERP chain loses its partial-completion length. __dasd_cleanup_cqr() then sees proc_bytes == 0 and completes the whole request instead of requeueing the remainder, silently returning zeroed data for the part that was never read. Carry proc_bytes over to the original request like the other per-request state.